How to fix Oasis Water Dispenser if the water is not cold enough?
To address a water dispenser that isn't chilling the water adequately, for LCD models, adjust the cold control to a colder setting. If you have a non-LCD model, rotate the cold control knob clockwise to a colder position. Allow two hours for the adjustment to take effect. If the water remains insufficiently cold after this period, further assistance is needed.
How to fix Oasis Water Dispenser that does not heat or chill water?
To troubleshoot an Oasis water dispenser that does not heat or chill water, begin by checking all electrical circuits, fuses, circuit breakers, and switches. Ensure the outlet is not switched and the temperature setting is not OFF (for non-LCD units, this means the cold control knob is not turned counter-clockwise as far as it will go). If the issue persists, the thermostat may be broken.
Why is the water from my Oasis Water Dispenser not cold enough?
For LCD models, adjust the cold control to 'COLDER' or 'COLDEST'. If it remains not cold after 2 hours, contact customer service. For non-LCD models, turn the cold control knob clockwise to a colder setting. If the water isn't colder after 2 hours, contact customer service.
What to do if my Oasis Aquabar 2 cooler does not heat or chill water?
First, check all electrical circuits, fuses, circuit breakers, and switches. Ensure the outlet isn't switched and the temperature isn't set to OFF (for non-LCD units, ensure the cold control knob isn't fully counter-clockwise). If the cooler still doesn't heat or cool, the thermostat may be broken; contact customer service.
What to do if no water comes out of cold faucet of Oasis Aquabar 2 Water Dispenser?
To resolve the issue of no water flowing from the cold faucet of your Oasis water dispenser: 1) First, check if water is coming out of the cook or hot faucet. If not, ensure that the main water supply is turned on. 2) Next, press the safety float reset button located on top of the cooler. Listen for the reservoir filling with water, or wait a few minutes before checking the cold faucet again. 3) Finally, if ice has accumulated inside the reservoir, for LCD models, set the cold setting to OFF on the display panel to allow the ice to melt. For non-LCD models, turn the cold control knob counterclockwise as far as it will go. Also, remove a side panel to ensure the cold control sensor is fully inserted into the thermowell.
Why Oasis Aquabar 2 Water Dispenser water is not hot enough?
To troubleshoot an Oasis water dispenser that isn't heating the water sufficiently, for LCD models, adjust the hot control to a hotter setting. Allow 20 minutes for the water to heat up after the initial setup. For non-LCD models, ensure the cooler is plugged in and has power. Check the hot tank switch on the column support to ensure it is set to the correct symbol. Allow 20 minutes for heating. If the water remains not hot after this time, further assistance is needed.
Why no water flows from the hot water tap of Oasis Aquabar 2?
If no water flows from the hot water tap of your Oasis water dispenser, it could be due to air bubbles preventing the water heater from filling. First, turn OFF the water supply and check the reservoir water level to ensure it's above the side outlet at the back. If the water level is adequate, turn the water supply back ON and press the hot dispense button for a few seconds to release any trapped air. If water still doesn't flow, turn OFF the water supply again, place a bucket below the hot tank drain at the back of the cooler, and open the drain to release any trapped air or blockages. Close the drain and restart the process.
Why is my Oasis Aquabar 2 water not hot enough?
For LCD models: Adjust the hot control to 'HOTTER' or 'HOTTEST'. It takes 20 minutes to heat up during the initial setup. If it's still not hot after 20 minutes, contact customer service. For NON-LCD models: Ensure the cooler is plugged in and has power. Check the hot tank switch on the column support to ensure it's on the 'I' symbol. Heating should begin immediately. It takes 20 minutes to heat up initially. If still not hot after 20 minutes, contact customer service.
What to do if no water comes out of the cold faucet of my Oasis Aquabar 2?
Check the cook or hot faucet. If no water comes out of those, make sure the water supply is on. Press the safety float reset button on the top of the cooler. Listen for water filling the reservoir or wait a few minutes and check the cold faucet again. If there is ice built up inside the reservoir: On an LCD model, lower the cold setting to OFF on the display panel and let the ice melt down. For a non-LCD model, turn the cold control knob counterclockwise as far as it will go. Remove a side panel and make sure the cold control sensor is inserted into the thermowell as far as it will go.
What to do if no water flows from the hot water tap of my Oasis Aquabar 2?
Air bubbles may prevent the water heater from filling up. Check the reservoir water level after turning OFF the water supply. Make sure the water level is above the side outlet at the back of the cooler. If the water level is adequate, turn ON the water supply. Press the hot dispense button for a few seconds to let the air out. If water still fails to flow out of the tap, turn OFF the water supply and place a bucket below the hot tank drain located at the back of the cooler and open the drain. There may be as much as 3 gallons of water that could drain out. Close the drain and restart the process. If it’s still not flowing, call customer service.
Highlights the child safeguard on the hot water dispenser button.
Step-by-step guide for installing the leak controller unit and its batteries.
Details initial cleaning steps for the water reservoir and baffle before first use.
Explains how to program the water cooler to save energy during specific times.
Instructions for setting the filter life monitor to track gallon usage.
Instructions for setting the UV bulb life monitor to track replacement intervals.
How to engage and disengage the control panel lock to prevent setting changes.
Detailed steps for washing and rinsing the water reservoir, baffle, and lids.
Instructions on preparing bleach solutions for sanitizing the water cooler components.
General| Brand | Oasis |
|---|---|
| Model | Aquabar 2 |
| Category | Water Dispenser |
| Language | English |
To Next Page
