Oki 42625502 - User Manual

1 page

Save Page as PDF

Warning!

If the printer has recently been powered on, some

fuser components will be very hot. Handle the fuser

with extreme care, holding it only by its handle, which

will only be mildly warm to the touch. A warning

label clearly indicates the area. If in doubt, switch

the printer off and wait at least 10 minutes for the

fuser to cool before opening the printer cover.

1. Press the cover release and open the printer's top cover fully.

2. Pull the two blue fuser lock levers (1) towards the front of the printer.

3. Holding the fuser by its handle, lift the fuser out of the printer. If the fuser is still

warm, place it on a flat surface which will not be damaged by heat. After letting

the fuser cool down, discard it.

5. Push the orange transport lock (1) to the left to release it (SNAP!), then

remove the transport lock.

6. Holding the new fuser by the handle, with the fuser pressure release lever

(1) on the right, lower the fuser into the priner.

7. Push the two blue retaining levers (1) toward the rear of the printer to lock

the fuser in place.

8.Close and latch the top cover.

①

58368302

①

4. Remove the new fuser from its packaging, then remove any packing tape.

Fuser Replacement for Oki 42625501 & 42625502

C3200/5150/C5200/C5400 Printers

Fuser Instructions

Questions and Answers

M
Mark PierceAug 30, 2025
Why does my Oki 42625502 say 'INSTALL PAPER CASSETTE 430: TRAY 1 MISSING'?
- S
  sydney49Aug 30, 2025
  If your Oki Printer displays 'INSTALL PAPER CASSETTE 430: TRAY 1 MISSING', it means Tray 1 is not installed. Install the missing tray to resolve the issue.
J
Jonathan YoungAug 29, 2025
How do I fix the 'CLOSE COVER 316: DUPLEX COVER OPEN' error on my Oki 42625502?
- A
  Amanda WadeAug 29, 2025
  To resolve the 'CLOSE COVER 316: DUPLEX COVER OPEN' error on your Oki Printer, ensure that the duplex cover is fully closed and properly latched.
M
Matthew ParkerAug 28, 2025
What does 'YYYY nnn: FATAL ERROR' mean on my Oki 42625502 Printer?
- P
  Patrick FigueroaAug 29, 2025
  If you see 'YYYY nnn: FATAL ERROR' on your Oki Printer, try turning it off and then back on. If the problem persists, write down the message, including the error number “nnn,” and any scrolling octets, then contact your authorized Oki Data Service Dealer.
R
Ronald ToddSep 12, 2025
How to enable interface on Oki 42625502 Printer?
- E
  Erin SpenceSep 12, 2025
  If the interface is disabled on your Oki Printer, check that the USB interface is set to Enable in the menu (USB MENU ? USB ? ENABLE).
J
jchapmanSep 15, 2025
Should I use a converter, buffer, extension cable or USB hub with Oki 42625502?
- J
  John LeeSep 15, 2025
  If a converter, buffer, extension cable, or USB hub is being used with your Oki Printer, test by connecting the printer and computer directly.
S
sarah25Sep 22, 2025
How to correctly configure printer driver for Oki 42625502?
- C
  cwebbSep 22, 2025
  If the printer driver is incorrectly configured for your Oki Printer, correctly configure the printer driver.
G
george94Aug 27, 2025
How to replace toner on Oki 42625502 Printer when it's empty?
- C
  Cassidy DyerAug 27, 2025
  To resolve a 'REPLACE TONER nnn: * TONER EMPTY' error on your Oki Printer, replace the indicated toner. The codes are: 410: Y = Yellow, 411 M = Magenta, 412: C = Cyan, 413: K = Black.
J
judy19Aug 26, 2025
What to do if Oki 42625502 does not go online?
- M
  Morgan PetersAug 26, 2025
  If your Oki Printer does not go online, switch it off and disconnect the power cable. Reconnect the power cable and switch the printer back on. If this does not clear the fault, call for service.
J
jasonhowellAug 26, 2025
Why does my Oki 42625502 Printer frequently jam?
- K
  Kelly LeeAug 26, 2025
  To address frequent paper jams in your Oki Printer, ensure the printer is on a stable, level surface and that you're using the correct type of paper. Store paper within specified temperature and humidity levels. Remove any creased or wrinkled paper, and adjust the tray or manual feed guides. Also, verify the correct paper feed selection in the printer driver's Properties Setup tab.
B
brianna27Aug 25, 2025
What to do if Oki 42625502 Printer doesn't print after clearing jam?
- Y
  yorkwilliamAug 26, 2025
  If your Oki Printer continues not to print after clearing a jam, raise and gently lower the top cover, especially if the paper jam was removed from behind the front cover.