EasyManuals Logo

Oki B411d Safety Information

Oki B411d
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
2 - English
Safety, Warranty and Regulatory Information
Safety Information,
120-Volt Models
Your OKI product has been carefully designed to give you
years of safe, reliable performance. As with all electrical
equipment, there are a few basic precautions you should
take to avoid hurting yourself or damaging the product.
Carefully read the provided setup and operating
instructions.
Save all provided documentation for future reference.
Read and follow all warning and instruction labels on the
product itself.
Unplug the product before you clean it. Use only a damp
cloth; do not use liquid or aerosol cleaners.
Place your product on a firm, solid surface. If you put it
on something unsteady, it may fall and be damaged. If
you place it on a soft surface, such as a rug, sofa, or
cushion, the vents may be blocked, causing the product
to overheat.
Protect your product from overheating. Make sure no
obstructions block the openings of the product. Do not
put the product on or near a heat source (such as a
radiator or heat register). Keep the product out of direct
sunlight.
Always use this product in a well ventilated area. Allow
enough room around the product for adequate
ventilation and easy access to the paper trays. If you put
the product in any kind of enclosure, make sure the
enclosure is well ventilated.
Do not use your product near water. Do not spill liquid of
any kind into it.
Be certain that your power source matches the rating
listed on the back of the product. If you are not sure,
check with your dealer or with your local power
company.
Do not connect this product to an uninterruptible power
supply (UPS). For further information please contact Oki
Data at 1-800-OKI-DATA.
Your product has a grounded, three-prong plug as a
safety feature. This plug only fits into a grounded outlet.
If the plug does not fit, the outlet may be an older,
non-grounded type. Contact an electrician to have the
outlet replaced. Do not use an adapter to defeat the
grounding.
Install the product near an easily accessed power outlet.
Avoid damaging the power cord. Do not put anything on
it or place it where it will be walked on. If the cord
becomes damaged or frayed, replace it immediately.
If you are using an extension cord or power strip with
the product, make sure that the total of the amperes
required by all the equipment on the extension is less
than the extension’s rating. The total ratings of all
equipment plugged into the outlet should not exceed 15
amperes.
Important! A telephone cable using 26 AWG wire or
larger must be used with this equipment.
Do not poke anything into the ventilation slots of the
product. You could get an electrical shock or cause
hazardous electrical arcing, which could cause a fire.
Aside from the routine maintenance described in the
documentation, do not try to service the product
yourself. Removing the cover may expose you to shocks
or other hazards.
Do not make any adjustments other than those outlined
in the documentation. You may cause damage that will
require extensive repair work. The provided
documentation explains how to get your product
serviced by qualified Oki Data technicians.
If anything happens that indicates that your product is not
working properly or has been damaged, unplug it
immediately and follow the procedures in the provided
documentation for having your product serviced.
Here are some of the things to look for.
The power cord or plug is frayed or damaged.
Liquid has been spilled into the product, or the product
has been exposed to water.
The product has been dropped, or the cabinet is
damaged.
The product does not function normally when you are
following the operating instructions.
Additional Safety Informaton for
Telecommunications Equipment
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the
following:
Do not use this product near water—for example, near a
bathtub, washbowl, kitchen sink or laundry tub—in a wet
basement, or near a swimming pool.
Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk
of electric shock from lightning.
Do not use the telephone to report a gas leak in the
vicinity of the leak.
Use only the power cord and batteries indicated in this
manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS.

Other manuals for Oki B411d

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Oki B411d and is the answer not in the manual?

Oki B411d Specifications

General IconGeneral
ColorNo
Print technologyLaser
Maximum resolution2400 x 600 DPI
Economical printingYes
Time to first page (black, normal)5 s
Print speed (black, normal quality, A4/US Letter)33 ppm
Processor model405
Processor familyPowerPC
Maximum internal memory320 MB
Sound power level (standby)30 dB
Sound pressure level (printing)54 dB
Total input capacity250 sheets
Total output capacity150 sheets
Maximum input capacity781 sheets
Total number of input trays1
Maximum number of input trays2
Multi-Purpose tray input capacity1 sheets
Bitmap fontsOCR-A, OCR-B
Printer fontsBitmap, PCL
Printing colorsBlack
Maximum duty cycle60000 pages per month
Recommended duty cycle3000 pages per month
Page description languagesEpson FX, IBM ProPrinter, PCL 5e, PCL 6, PostScript 3
Envelopes sizes7 3/4, 9, 10, C5, C6, DL
Maximum print size216 x 356 mm
Paper tray media typesBanner, Envelopes, Plain paper
Paper tray media weight60 - 120 g/m²
Non-ISO print media sizesExecutive (184 x 267mm), Legal (media size), Letter (media size), Statement (140 x 216mm)
ISO A-series sizes (A0...A9)A4, A5, A6
JIS B-series sizes (B0...B9)B5
Maximum ISO A-series paper sizeA4
Multi-Purpose Tray media weight60 - 163 g/m²
Power requirements230V
Compatible operating systemsWindows 2000/2003/XP/Server 2008/Vista/7 Mac OS 10.3.9 +
AC input frequency50 - 60 Hz
Power consumption (printing)900 W
Power consumption (PowerSave)8 W
Display-
Sustainability certificatesENERGY STAR
Storage temperature (T-T)-10 - 43 °C
Operating temperature (T-T)10 - 32 °C
Storage relative humidity (H-H)10 - 90 %
Operating relative humidity (H-H)20 - 80 %
Standard interfacesParallel, USB 2.0
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Weight and Dimensions IconWeight and Dimensions
Dimensions (WxDxH)387 x 364 x 244.5 mm

Related product manuals