Oki MB472w Safety And Warranty Guide

5 - English
Regulatory Information
Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired
Responsible Party:
Oki Data Americas, Inc.
8505 Freeport Pkwy, Suite 600
Irving, TX 75063, U.S.A.
1-856-235-2600
FCC Radio Frequency Interference Statement
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Plug the unit into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.
FCC Administrative Council for Terminal
Attachment Requirements for End Users
This device has been granted a registration number by the
Administrative Council for Terminal Attachment (ACTA),
under Part 68 and ACTA rules and regulations for direct
connection to the telephone lines. In order to comply with
these FCC rules, the following instructions must be carefully
read and applicable portions followed completely.
1.This equipment complies with Part 68 of FCC rules and
the requirements adopted by the ACTA. On the back of
the equipment is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this information must
be provided to the telephone company.
2.The following USOC jacks may be used with this
equipment: RJ11C.
3. A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed
to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
4. The REN is used to determine the quantity of devices
which may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not
all areas, the sum of the RENs should not exceed five
(5.0). To be certain of the number of devices that may be
connected to the line, as determined by the total RENs,
contact the local telephone company. For products
approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the
label.
5. If the equipment, MB472w/MB492/MB562w, causes harm
to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer
as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is
necessary.
6. The telephone company may make changes in its
facilities, equipment, operations, or procedures that could
affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make the necessary modifications to maintain
uninterrupted service.
7. If trouble is experienced with this equipment (MB472w/
MB492/MB562w), please contact the following for repair
and/or warranty information:
Oki Data Americas, Inc.
8505 Freeport Pkwy, Suite 600
Irving, TX 75063, U.S.A.
Telephone:(856) 235-2600 or
(800)-OKIDATA (800-654-3282)
If the equipment is causing harm to the telephone
network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
8. This equipment contains no user serviceable parts. Please
contact Oki Data for service.
Product Name Model Name
MB472w, 120 V N22502A
MB492, 120 V N22503A
MB562w, 120 V N22504A

Oki MB472w Specifications

General

Brand	Oki
Model	MB472w
Category	All in One Printer
Language	English