Omega CN8EPt - Page 26

To Next Page

To Previous Page

PLATINUM

Series Controllers User’s Guide

M5451 Omega Engineering | www.omega.com

Complete Menu Structure

Level

Notes

Stby

Standby Mode, outputs, and Alarm conditions disabled, displays Stby

tARE

TARE option - only available if enabled in INPt

Main Page

Table of Contents3
Introduction8
Description8
Safety Considerations9
Wiring Instructions10
Back Panel Connections10
(No Isolated Output Expansion Board Installed)10
(With Isolated Output Expansion Board)10
Connecting Power11
Connecting Inputs12
Connecting Outputs14
PLATINUM TM Series Navigation16
Description of Button Actions16
Menu Structure16
Level 1 Menu17
Circular Flow of Menus17
Complete Menu Structure18
Initialization Mode Menu (Init)18
Programming Mode Menu (Prog)22
Operating Mode Menu (Oper)25
Reference Section: Initialization Mode (Init)27
Input Configuration (Init > Inpt)27
Thermocouple Input Type (Init > Inpt > T.C.)27
Resistance Temperature Detector (RTD) Input Type (Init > Inpt > Rtd)28
Thermistor Input Type Configuration (Init > Inpt > Thrm)28
Process Input Type Configuration (Init > Inpt > Proc)29
TARE (Init > Tare)34
LINR (Init > LINR)34
Display Reading Formats (Init > Rdg)36
Decimal Point Format (Init > Rdg > Dec.p)36
Temperature Units (Init > Rdg > °F°C)36
Display Rounding (Init > Rdg > D.rnd)37
Filter (Init > Rdg > Fltr)37
Annunciator Settings (Init > Rdg > ANN.1/ANN.2)38
Normal Color (Init > Rdg > NCLR)38
Brightness (Init > Rdg > Brgt)38
Excitation Voltage (Init > Ectn)39
Communication (Init > Comm)39
Protocol (Init > Comm > Usb, Ethn, SER > Prot)39
Address (Init > Comm > Usb, Ethn, SER > Addr)40
Serial Communications Parameters (Init > Comm > SER >C.PAR)41
Safety Features (Init > Sfty)42
Power on Confirmation (Init > Sfty > Pwon)42
Operating Mode Confirmation (Init > Sfty > Oper)42
Setpoint Limits (Init > Sfty > SP.LM)43
Loop Break Timeout (Init > Sfty > SEN.M > Lpbk)43
Open Circuit (Init > Sfty > SEN.M > O.crk)43
Sensor Error Latch (Init > Sfty > SEN.M > E.LAT)43
Output Break Detection (Init > Sfty > OUT.M > O.brk)44
Output Error Latch (Init > Sfty > OUT.M > E.LAT)44
Manual Temperature Calibration (Init > T.cal)44
No Manual Temperature Calibration Adjustment (Init > T.cal > None)45
Manual Temperature Calibration Offset Adjustment (Init > T.cal > 1.Pnt)45
Manual Temperature Calibration Offset and Slope Adjustment (Init > T.cal > 2.Pnt)45
Temperature Ice Point Calibration (Init > T.cal > ICE.P)46
Save Current Configuration for All Parameters to a File (Init > SAVE)46
Load a Configuration for All Parameters from a File (Init > Load)46
Display Firmware Revision Number (Init > VER.N)46
Update Firmware Revision (Init > VER.U)47
Reset to Factory Default Parameters (Init > F.dft)47
Password-Protect Initialization Mode Access (Init > I.pwd)47
Password-Protect Programming Mode Access (Init47
Reference Section: Programming Mode (Prog)48
Setpoint 1 Configuration (Prog > SP1)48
Setpoint 2 Configuration (Prog > SP2)48
Alarm Mode Configuration (Prog > ALM.1, ALM.2)49
Alarm Type (Prog > ALM.1, ALM.2 > Type)49
Absolute or Deviation Alarm (Prog > ALM.1, ALM.2 > Type > Ab.DV)50
Alarm High Reference (Prog > ALM.1, ALM.2 > Type > ALR.H)50
Alarm Low Reference (Prog > ALM.1, ALM.2 > Type > ALR.L)51
Alarm Color (Prog > ALM.1, ALM.2 > A.CLR)51
Alarm High High / Low Low Offset Value (Prog > ALM.1, ALM.2 > HI.HI)51
Alarm Latching (Prog > ALM.1, ALM.2 > Ltch)52
Alarm Normally Closed, Normally Open (Prog > ALM.1, ALM.2 > Ctcl)52
Alarm Power-On Behavior (Prog > ALM.1, ALM.2 > a52
Alarm on Delay (Prog > ALM.1, ALM.2 > De.on)52
Alarm off Delay (Prog > ALM.1, ALM.2 > De.of)53
Output Channel 1-6 Configuration (Prog > Out.1-Out.6)53
Output Channel Mode (Prog > Out1-Out6 > Mode)54
Output Cycle Pulse Width (Prog > Out1-Out6 > Cycl)56
Analog Output Range (Prog > Out1-Out6 > RNGE)57
PID Configuration (Prog > Pid.s)58
Action Response (Prog > Pid > Actn)58
Autotune Timeout (Prog > Pid > A.to)58
Autotune (Prog > Pid > TUNE)58
PID Gain Settings (Prog > Pid > GAIN)59
Relative Cool Gain (Prog > Pid > Rcg)60
Control Offset (Prog > Pid > Ofst)60
Deadband (Prog > Pid > Dead)60
Low Output Clamping Limit (Prog > Pid > %Lo)60
High Output Clamping Limit (Prog > Pid > %HI)61
Adaptive Tuning (Prog > Pid > Adpt)61
PID.2 Configuration (Prog > Pid.2)61
Remote Setpoint Configuration (Prog > RM.SP)61
Cascade Control Using Remote Setpoint63
Multi-Ramp/Soak Mode Parameters (Prog > M.RMP)64
Multi-Ramp/Soak Mode Control (Prog > M.RMP > R.ctl)64
Select Program (Prog > M.RMP > S.PRG)65
Multi-Ramp/Soak Tracking (Prog > M.RMP > M.trk)65
Time Format (Prog > M.RMP > Tim.f)65
Program End Action (Prog > M.RMP > E.ACT)66
Number of Segments (Prog > M.RMP > N.SEG)66
Segment Number for Editing (Prog > M.RMP > S.SEG)66
More on Multi-Ramp/Soak Programming67
Reference Section: Operating Mode (Oper)69
Normal Run Mode (Oper > RUN)69
Change Setpoint 1 (Oper > SP1)69
Change Setpoint 2 (Oper > SP2)70
Manual Mode (Oper > MANL)70
Pause Mode (Oper > PAUS)71
Stop Process (Oper > Stop)71
Clear Latched Alarms (Oper > L.rst)71
Display Valley Reading (Oper > Valy)71
Display Peak Reading (Oper > Peak)72
Standby Mode (Oper > Stby)72
Standby Mode (Oper > Tare)72
Specifications73
Inputs73
Control73
Outputs74
Communications (USB Standard, Optional Serial and Ethernet)74
Isolation74
General75
Approvals Information77

Omega CN8EPt - Page 26

Table of Contents

Related product manuals