How to fix Over Temp Fault on Omnik Inverter?
If your Omnik Inverter displays an 'Over Temp Fault', it means the internal temperature is too high. Try to lower the ambient temperature around the inverter or relocate it to a cooler place.
What to do if my Omnik Inverter shows a 'No Utility' error?
If your Omnik Inverter shows a 'No Utility' error, the grid might not be connected. Check the grid connection cables and ensure the grid is working. If the grid is fine, the inverter's fuse might be open, so please call a service technician.
Why does my Omnik Inverter show a Current Fault?
If your Omnik Inverter displays 'Current Fault,' this indicates that the ground current is too high. Disconnect the AC side, then unplug the inputs from the PV generator and inspect the peripheral AC system. Once the issue is resolved, reconnect the PV panel and AC connection, and check the PV-Inverter status.
What does PV Voltage Fault mean on Omnik Inverter?
If your Omnik Inverter shows 'PV Voltage Fault', check if the open PV voltage is greater than or close to 590VDC (for Omniksol-3k-TL2, Omniksol-4k-TL2, or Omniksol-5k-TL2 models). If the PV voltage is less than 590VDC and the problem persists, contact local service.
How to troubleshoot Isolation Fault on Omnik Inverter?
If your Omnik Inverter displays 'Isolation Fault', check the impedance between PV (+) & PV (-) and the inverter's earth connection. The impedance must be greater than 2MΩ. Also, verify that the AC side is not in contact with earth.
What causes Master Grid Freq Fault or Master Grid Volt Fault on Omnik Inverter?
If your Omnik Inverter shows 'Master Grid Freq Fault' or 'Master Grid Volt Fault', wait for a moment. If the grid returns to normal, the inverter will automatically restart. Ensure that the grid voltage and frequency meet the required specifications.
How do I fix ENS Grid Voltage Fault or ENS Grid Freq Fault on Omnik Inverter?
If your Omnik Inverter displays 'ENS Grid Voltage Fault' or 'ENS Grid Freq Fault,' disconnect PV (+) or PV (-) from the input and restart the inverter.
What to do for Relay1 Fault or Relay2 Fault on Omnik Inverter?
If your Omnik Inverter displays 'Relay1 Fault' or 'Relay2 Fault', disconnect ALL PV (+) or PV (-). Wait a few seconds until the LCD switches off, then reconnect and check again. If the problem remains, please call local service.
Defines the manual's purpose and the inverter models covered.
Explains DANGER, WARNING, and CAUTION hazard symbols.
Identifies intended users and required qualifications for operation.
Outlines critical safety precautions for using the inverter.
Details various warning and informational symbols found on the inverter.
Introduces the inverter's design, layout, and heat dissipation features.
Lists key features like efficiency, reliability, and protection methods.
Provides detailed technical specifications for the Omniksol inverter models.
Directs users to support channels like website and hotline.
Lists all components included in the inverter package.
Shows and labels the front and bottom parts of the inverter.
Explains how to identify the inverter using its nameplate details.
Provides contact details for additional support and information.
Covers DANGER and NOTICE warnings for safe inverter installation.
Guides on proper vertical installation, wall support, and environmental factors.
Specifies required distances around the inverter for ventilation and access.
Step-by-step instructions for attaching the mounting bracket to the wall.
Details how to use a padlock to secure the inverter to the bracket.
Highlights DANGER and NOTICE for safe electrical connections.
Instructions for connecting the AC power output, including assembly steps.
Instructions for connecting DC power input from PV panels, including MC4 assembly.
Explains RJ45 ports for data communication and monitoring setup.
Identifies LCD screen elements, buttons, and LED status indicators.
Guides through the initial setup and configuration process.
Details how to operate the inverter, including system interfaces, status, and modes.
Explains navigation to Safety, Info, Error, and Set modes.
Lists and explains all operational states and fault codes.
To Next Page
General