Why is my Omron Avail PM601 Medical Equipment intensity too weak?
The intensity may be weak for several reasons: the pads may be stacked or overlapping (check their placement), TENS therapy might not be selected ('MICROCURRENT' will prevent you from feeling intensity), the intensity setting could be too low (increase it in the app), or the pad's adhesive surface may be damaged (replace the pad).
What to do if my Omron Avail PM601 Medical Equipment power cuts off during use?
The power may be cutting off because the battery charge is extremely low (recharge it fully). Also, the device automatically turns off 10 minutes after therapy completion, pad removal, or therapy pausing, so check if any of these have occurred and ensure the pad is correctly placed on your body.
Why won't my Omron Avail PM601 device recharge?
The device might not be recharging because the battery charger isn't connected properly, so check the AC adapter connection to both the charger and the power outlet. Also, ensure the device is properly placed on the charger without any foreign objects. High heat or cold temperatures can also stop the battery from recharging, potentially increasing the charging time.
What to do if Omron Avail PM601 shows connection failure?
If your device shows a connection failure, it might be too far from your smartphone. Move the device within 16 ft (5 m) of the smartphone. Also, consider if the Omron TENS app was uninstalled and reinstalled.
How to fix Omron Avail PM601 Medical Equipment pad not sticking to skin?
If the pad isn't sticking, make sure you've removed the transparent film from the adhesive surface. Also, if the pad or your skin is wet, air dry both surfaces. If the adhesive surface is damaged, replace the pad. Shave the area if there is too much hair on your skin. Replace the pad if it was stored under high temperature, high humidity or direct sunshine.
What to do if Omron Medical Equipment skin turns red or feels irritated?
If your skin becomes red or irritated, shorten the therapy session to less than 30 minutes. Ensure the pads are placed correctly on your body, and replace the pad if the adhesive surface is worn out.
How to fix Omron Avail PM601 Medical Equipment unable to tap start button?
If you're unable to tap the 'START' button, check that the pads are properly placed on your body, and ensure the device is correctly attached to the pad. Also, verify that you've removed the transparent film from the pad's adhesive surface. The pad may also be damaged, so consider replacing it. Also, make sure that the device power is on and connected to the app.
Why won't my Omron Avail PM601 device turn on?
The device might not be turning on because the batteries are depleted. If so, recharge the battery fully.
What does blinking purple light mean on Omron Avail PM601 Medical Equipment?
The blinking purple light indicates abnormalities in the device. Stop using it immediately.
What to do if Omron Avail PM601 Medical Equipment devices are hot when charging?
If the devices, charger, or AC adapter are abnormally hot during charging, they may be damaged. Unplug the AC adapter from the charger and remove the device from the charger immediately.
General| Category | Medical Equipment |
|---|---|
| Device Type | Blood Pressure Monitor |
| Model | PM601 |
| Technology | Oscillometric |
| Battery Life | Approximately 300 measurements (with new alkaline batteries) |
| Data Storage | 60 readings |
| Intended Use | Home blood pressure monitoring |
| Cuff Size | 22-32cm |
| Pressure Range | 0-299mmHg |
| Pulse Rate Range | 40 to 180 beats/min |
Important safety information for safe and proper use of the device.
Device's purpose for pain relief in muscles and joints due to strain.
Reasons why the device should not be used, e.g., pacemakers.
Critical safety precautions to prevent serious injury or death.
Precautions to prevent minor injury or equipment damage.
Guidelines for cleaning the skin and correctly placing the pads on various body parts.
Critical areas where pads should not be applied due to safety risks.
Common issues and their solutions for device operation and connectivity.
To Next Page
