Omron NJ Series Troubleshooting Manual

3 Error Tables
3-34
NJ-series Troubleshooting Manual (W503)
5401545E hex Motion Control
Instruction Re-exe-
cution Disabled
(MoveMode)
An attempt was made to
change the parameter for
the MoveMode input vari-
able when re-executing a
motion control instruction.
(This input variable cannot
be changed when re-exe-
cuting an instruction.)
• A parameter for an
input variable that can-
not be changed for re-
execution was
changed.
S NJ-series
Instruc-
tions Ref-
erence
Manual
(Cat. No.
W502)
5401545F hex Illegal Auxiliary
Axis Specification
The axis specified for the
Auxiliary input variable to a
motion control instruction
does not exist.
• An axis does not exist
for the variable speci-
fied for the Auxiliary
input variable to the
instruction.
S Same as
above.
54015460 hex Illegal Axis Specifi-
cation
The axis specified for the
Axis input variable to a
motion control instruction
does not exist.
• An axis does not exist
for the variable speci-
fied for the Axis input
variable to the instruc-
tion.
S Same as
above.
54015461 hex Illegal Axes Group
Specification
The axes group specified
for the AxesGroup input
variable to a motion control
instruction does not exist or
is not a used group.
• An axes group does
not exist for the vari-
able specified for the
AxesGroup input vari-
able to the instruction.
• The axes group speci-
fied for the AxesGroup
input variable to the
instruction is not spec-
ified as a used group.
S Same as
above.
54015462 hex Illegal Master Axis
Specification
The axis specified for the
Master input variable to a
motion control instruction
does not exist or is not a
sync master axis.
• An axis does not exist
for the variable speci-
fied for the Master
input variable to the
instruction.
• The axis that was
specified for the Mas-
ter input variable to
the
MC_Phasing (Shift
Master Axis Phase)
instr
uction is not the
master axis fo
r sync-
ing.
S Same as
above.
54015463 hex Motion Control
Instruction Re-exe-
cution Disabled
(SlaveOffset)
An attempt was made to
change the SlaveOffset
input variable when re-exe-
cuting a motion control
instruction. (This input vari-
able cannot be changed
when re-executing an
instruction.)
• A parameter for an
input variable that can-
not be changed for re-
execution was
changed.
S Same as
above.
54015464 hex Motion Control
Instruction Re-exe-
cution Disabled
(SlaveScaling)
An attempt was made to
change the SlaveScaling
input variable when re-exe-
cuting a motion control
instruction. (This input vari-
able cannot be changed
when re-executing an
instruction.)
• A parameter for an
input variable that can-
not be changed for re-
execution was
changed.
S Same as
above.
54015465 hex Motion Control
Instruction Re-exe-
cution Disabled
(StartPosition)
An attempt was made to
change the StartPosition
input variable when re-exe-
cuting a motion control
instruction. (This input vari-
able cannot be changed
when re-executing an
instruction.)
• A parameter for an
input variable that can-
not be changed for re-
execution was
changed.
S Same as
above.
Event code Event name Meaning Assumed cause
Level
Refer-
ence
Maj Prt Min Obs Info

Omron NJ Series Specifications

General

Program Capacity	Up to 128 MB
SD Card Slot	Yes
Power Supply Voltage	24 VDC
Motion Control	Yes
USB Ports	1
Operating Temperature	0°C to 55°C
Communication Interfaces	Ethernet/IP, EtherCAT, USB
Safety Function	Optional
Storage Temperature	-20°C to 75°C
Communication Ports	USB
Dimensions	Varies by model
Weight	Varies by model