Onkyo A-8170 Instruction Manual

Trouble shooting guide
No power.
not clear.
Specitications
Trouble
Power on but no sound.
Hum, low frequency noise.
Howling when the volume is turned up.
together.
Rough or schatchy sound. High range is | @ Stylus of pick-up is worn.
@ Stylus is dirty.
@ AC fuse blown.
® Poor or no input ground.
® Poor or no phono motor ground.
® Turntable and speakers are too close
® Treble control is too high.
@ Clean.
Continuous Power Output:
Dynamic Power:
Total Harmonic Distortion
Intermodulation Distortion:
Damping Factor:
Input Sensitivity/
Impedance
Output Level/Impedance:
Phono Overload:
Tone Control
(Vol — 20 dB):
High Cut:
Frequency Response:
RIAA Deviation:
Signal to Noise
Ratio (IHF-A):
Muting (Vol —20 dB):
Power Supply:
Dimensions (W x H x D):
Weight:
A-8190
2 x 150 watts at 4 ohms, 1 kHz (DIN)
2 x 115 watts at 8 ohms, 1 kHz (DIN)
100 watts per channel, min. RMS, at 8 ohms,
both channels driven from 20 Hz to 20 kHz,
with no more than 0.008% Total harmonic
distortion.
2 x 303 watts at 2 ohms,
2 x 235 watts at 4 ohms
0.008% at rated power
0.008% at 1 watt output
0.005% at rated power
50 at 8 ohms
Phono (MM): 2.5 mV/50 kohms
Phono (MC): 160 pV/220 ohms
CD, DIRECT: 150 mV/50 kohms
TUNER: 150 mV/50 kohms
Tape Play: 150 mV/50 kohms
VCR Play: 150 mV/50 kohms
VDP Play: 150 mV/50 kohms
Tape Rec: 150 mV/1.5 kohms (Phono)
Pre Out: 1 V/600 ohms
Phono (MM): 200 mV RMS. at 1 kHz,
0.012% THD.
CONTRABASS: +10/+20 dB
(Muting: OFF/ON)
at 20 Hz
BASS: +10 dB at 70 Hz
TREBLE: +8 dB at 20 kHz
6 kHz (6 dB/Octave) (TREBLE min.)
CD, Tuner: 2 Hz—50 kHz
(+0, -1 dB)
Phono (MM): +£0.3 dB, 20 Hz -20 kHz
Phono (MM): 94 dB (5 mV input)
Phono (MC): 75 dB (0.5 mV input)
CD DIRECT: 107 dB
-15 dB
European models: AC220V, 50 Hz
Canadian models: AC120V, 60 Hz
U.K & Australia models: AC240V, 50 Hz
Worldwide models: AC120 and 220V
switchable, 50/60 Hz
435 x 157 x 396 mm
17-1/8" x 6-3/16”" x 15-9/16”"
13.2 kg, 29.1 Ibs.
Continuous Power Output:
Dynamic Power:
Tota! Harmonic Distortion
Intermodulfation Distortion:
Damping Factor:
Input Sensitivity/
impedance
Output Level/Impedance:
Phono Overload:
Tone Control
(Vol -20 dB):
High Cut:
Frequency Response:
RIAA Deviation:
Signal to Noise
Ratio (IHF-A):
Muting:
Power Supply:
Dimensions (W x H x D):
Weight:
® Contact Onkyo dealer.
® Check input leads, speaker leads, pin plugs, etc.
@ Check outer conductor of input plugs.
@ Check for proper ground connection.
@ Move them farther apart.
@ Replace.
@ Turn treble control down.
A-8170
2 x 120 watts at 4 ohms, 1 kHz (DIN)
2 x 90 watts at 8 ohms, 1 kHz (DIN)
80 watts per channel, min. RMS, at 8 ohms,
both channels driven from 20 Hz to 20 kHz,
with no more than 0.008% Total harmonic
distortion.
2 x 210 watts at 2 ohms,
2 x 167 watts at 4 ohms
0.008% at rated power
0.008% at 1 watt output
0.005% at rated power
50 at 8 ohms
Phono (MM): 2.5 mV/50 kohms
Phono (MC): 160 pV/220 ohms
CD, DIRECT: 150 mV/50 kohms
TUNER: 150 mV/50 kohms
Tape Play: 150 mV/50 kohms
VCR Play: 150 mV/50 kohms
VDP Play: 150 mV/50 kohms
Tape Rec: 150 mV/1.5 kohms ( Phono)
Phono (MM): 200 mV RMS. at 1k Hz,
0.015% THD.
CONTRABASS: +10 dB at 20 Hz
BASS: +10 dB at 70 Hz
TREBLE: +8 dB at 20 kHz
6 kHz (6 dB/Octave) (TREBLE min)
CD, Tuner: 2 Hz —50 kHz
(+0, —7 dB)
Phono (MM): +0.3 dB 20 Hz —20 kHz
Phono (MM): 93 dB (5 mV inpul
Phono (MC): 74 dB (0.5 mV input)
CD DIRECT: 107 dB
-20 dB
European models: AC220V, 50 tz
Canadian models: AC120V, 60 kz
U.K & Australia models: AC240V, §) Hz
Worldwide models: AC120 and 20V
switchable, 50/60 Hz
435 x 147 x 388 mm
17-1/8”" x 5-13/16” x 15-5/16"
11.2 kg, 24.7 Ibs
Specifications and features are subject to change witio ut notice.

Onkyo A-8170 Specifications

General

Damping Factor	60 (8 Ω, 1 kHz)
Speaker Load Impedance	4 Ω-16 Ω
Type	Integrated Amplifier
Frequency Response	5 Hz-100 kHz
Input Sensitivity	2.5 mV (MM), 150mV (line)
Signal to Noise Ratio	80 dB (MM), 105 dB (Line)
Input Impedance	47kΩ (line)
Dimensions	435 x 142 x 391mm