Onkyo HT-S5910 User Manual

82
Front Panel≫ Rear Panel≫ Remote≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
2. Speaker
 1. Conguration
Change the settings of connection environment of the speakers.
Setting Item Default Value Setting Details
Speaker
Channels
5.1.2 ch Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1
ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch" or
"5.1.2 ch" to suit the number of speaker channels
connected.
Subwoofer Yes Set whether a subwoofer is connected or not.
"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected
Height Speaker Bundled Dolby
Speaker
Set the speaker type if height speakers are
connected to the SURROUND BACK or HEIGHT
terminals.
Select "Bundled Dolby Speaker", "Front High",
"Top Front", "Top Middle", "Top Rear", "Rear High",
"Dolby Speaker (Front)" or "Dolby Speaker (Surr)"
according to the type and layout of the connected
speakers.
• If the item cannot be selected even though
connection is correct, check if the setting in
"Speaker Channels" matches the number of
connected channels.
Zone B Speaker No Set whether speakers are connected to Zone B
speaker terminals.
"Yes": When speakers are connected to Zone B
speaker terminals
"No": When speakers are not connected to Zone B
speaker terminals
• This setting is xed to "No" if "Bi-Amp" is set to
"Yes".
• This setting cannot be selected when surround
back speakers or height speakers are installed.
Setting Item Default Value Setting Details
Zone B Output
Level
Fixed Select whether to adjust the volume on the premain
amplier in the separate room or on this unit when
outputting to Zone B.
"Fixed": Adjust on the pre-main amplier in the
separate room
"Variable": Adjust on this unit
• This setting is xed to "Variable" if "Zone B
Speaker" is set to "Yes".
• This setting is xed to "Variable" if "Bi-Amp" is
set to "Yes".
Bi-Amp No Set whether the front speakers are bi-amp
connected.
"No": When front speakers are not bi-amp
connected
"Yes": When front speakers are bi-amp connected
• This setting is xed to "No" if "Zone B Speaker"
is set to "Yes".
• This setting cannot be selected when surround
back speakers or height speakers are installed.
Speaker
Impedance
6 ohms or above Set the impedance (Ω) of the connected speakers.
"4 ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance
"6 ohms or above": When the connected speakers
all have 6 Ω or more impedance
• For impedance, check the indications on the
back of the speakers or their instruction manual.

Onkyo HT-S5910 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
4Ω speaker support	No
Audio output channels	5.1.2 channels
Total Harmonic Distortion (THD)	0.08 %
Dynamic power per channel (3 Ohm)	160 W
Power output per channel (20-20KHz@8 Ohm)	115 W
Display	LCD
Product color	Black
Audio decoders	Dolby Atmos
Damping factor	60
Amplifier output power	925 W
HDMI in	4
Composite video in	3
Digital audio coaxial in	1
Digital audio optical in	2
Ethernet LAN (RJ-45) ports	0
Audio (L/R) out	7
Connectivity technology	Wired
Speakers connectivity type	Clamp terminals
Supported radio bands	AM, FM
AC input voltage	120 V
AC input frequency	60 Hz

Weight and Dimensions

Depth	328 mm
Width	453 mm
Height	160 mm
Weight	7800 g