EasyManuals Logo

Onkyo M-282 User Manual

Onkyo M-282
7 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
Rear
panel
facilities
and
connections
Caution:
•
Be
sure
to
always
refer
to
the
instructions
that
came
with
the
component
that
you
are
connecting.
•
Do
not
plug
in
the
power
cord
until
all
connections
have
been
made.
•
Do
not
make
connections
to
input
or
output
jacks
while
the
M-282
is
turned
on.
•
Always
turn
the
volume
of
the
control
amplifier
or
preamplifier
down
before
turning
on
the
M-282.
•
For
input
and
output
jacks,
red
connectors
(marked
R)
are
used
for
the
right
channel
and
white
connectors
(marked
L)
are
used
for
the
left
channel.
Insert
all
plugs
and
connectors
securely.
Improper
connections
can
result
in
noise,
poor
performance,
or
damage
to
the
Do
not
bind
audio
connection
cables
with
power
cords
and
speaker
cables.
Doing
so
may
adversely
affect
the
sound
quality.
rn
gnd
Use
this
GND
terminal
for
connecting
the
ground
(or
earth)
wire
of
other
component
if
humming
noise
is
heard.
2
1
AUDIO
IN/OUT
These
are
the
analog
audio
inputs
and
outputs.
Use
an
RCA-type
audio
connection
cable
to
connect
the
output
jacks
of
the
device
to
the
AUDIO
IN
jacks
on
the
M-282.
When
connecting
a
control
amplifier
or
preamplifier,
connect
the
PRE
OUT
jacks
to
the
AUDIO
IN
jacks.
If
you
connect
the
AUDIO
OUT
jacks
of
the
M-282
to
the
AUDIO
IN
jacks
of
another
M-282,
the
signal
input
at
the
AUDIO
IN
jacks
of
the
M-282
is
also
output
from
the
AUDIO
OUT
jacks
(Audio
In/Out
Link
Function).
If
you
set
the
TRIGGER
switch
to
AUDIO,
the
power
of
the
connected
M-282
turns
on
automatically
when
an
audio
signal
is
supplied
to
the
AUDIO
IN
jacks
(Auto
Power
On/Off
Function),
3
I
INPUT
LEVEL
Turn
this
INPUT
LEVEL
control
to
adjust
the
input
level
of
the
signal
from
the
AUDIO
IN
jacks.
Normally,
set
to
MAX.
4|
TRIGGER
Set
this
TRIGGER
switch
before
turning
on
the
M-282.
To
turn
on
the
M-282
with
the
^signal
input
from
the
12V
TRIGGER
IN
jack,
set
the
TRIGGER
switch
to
12V
TRIGGER.
To
turn
on
the
M-282
with
the
signal
input
from
the
AUDIO
IN
jack,
set
the
TRIGGER
switch
to
AUDIO
(Auto
Power
On/Off
Function).
If
you
do
not
use
Auto
Power
Function,
set
the
TRIGGER
switch
to
OFF.
5|
12V
TRIGGER
IN
If
the
connected
control
amplifiers
or
preamplifiers
have
a
12V
TRIGGER
output
jack,
use
1/8-inch
2P
mini-jack
cable
to
connect
the
12V
TRIGGER
IN
jack
on
the
M-282.
This
jack
works
on
between
5
to
12
volts
DC.
When
the
M-282
is
in
the
standby
state
and
the
TRIGGER
switch
is
set
to
12V
TRIGGER,
you
can
switch
the
M-282
between
the
on
and
standby
states
with
operations
at
the
control
amplifier
or
preamplifier.
Note:
When
a
plug
is
connected
to
the
12V
TRIGGER
jack,
be
sure
to
connect
the
analog
output
jacks
(or
PRE
OUT
jacks)
of
the
device
to
the
AUDIO
IN
jacks
of
the
M-282.
Otherwise,
no
sound
will
be
produced.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Onkyo M-282 and is the answer not in the manual?

Onkyo M-282 Specifications

Power Output IconPower Output
power output per channel (8 ohms)100 Watts
power output per channel (6 ohms)125 Watts
dynamic power output (8 ohms)140 Watts
Power and Consumption IconPower and Consumption
power supply voltageAC 120 V
power consumption2.5 A
rated speaker impedance6 ohms MIN
Performance IconPerformance
frequency response10 Hz - 100 kHz, ±1 dB
signal-to-noise ratio110 dB (IHF A, 0.5 V input)
total harmonic distortion0.08 % at rated power
Weight and Dimensions IconWeight and Dimensions
dimensions435 x 145 x 316 mm
weight8.5 kg
weight (imperial)18.7 lbs
View in Manual

Related product manuals