Onson J10C - User Manual

Questions and Answers

A
Angela OconnorAug 18, 2025
Why Onson J10C does not clean automatically as scheduled?
- L
  lshannonAug 18, 2025
  There are several reasons why your Onson Vacuum Cleaner might not be cleaning automatically as scheduled: 1. The power switch of the cleaner is not on. Make sure to turn on the cleaner's power source. 2. The cleaner's battery power is low. When the cleaner is on standby, keep it charging on the charging stand to ensure it's always fully charged. 3. The cleaner's parts are obstructed or tangled by garbage. Turn off the power, clean the dust box, turn the cleaner upside down, and clean the parts separately.
T
Tiffany HuberAug 20, 2025
What to do if Onson J10C could not recharge?
- T
  tuckeramandaAug 20, 2025
  If your Onson Vacuum Cleaner isn't recharging, it could be due to: * Insufficient contact: Ensure the charging poles of the cleaner and charging dock are fully connected. * Power supply issues: If the charging dock's power supply is off while the cleaner's power switch is on, it can lead to power loss. When the cleaner is not in use, keep it in the charging status to maintain optimal performance for the next task.
K
karenhenryAug 22, 2025
What to do if Onson Vacuum Cleaner remote controller malfunction?
- M
  Matthew StricklandAug 23, 2025
  If your Onson Vacuum Cleaner's remote controller is malfunctioning, consider the following: 1. Remoter battery power load: Replace the old battery with a new one, ensuring correct installation. 2. Cleaner power issues: Ensure the cleaner's power switch is on and that it has sufficient power. 3. Dirty sensors: Wipe the infrared transmitter on the remote control and the infrared receiver on the cleaner with a clean cotton cloth. 4. Infrared interference: Avoid using the remote control near other infrared devices.
T
Tim WilcoxAug 26, 2025
Why Onson J10C returns to charge before cleaning is completed?
- J
  Joseph CookAug 26, 2025
  If your Onson Vacuum Cleaner returns to charge before finishing the cleaning, try charging the cleaner. Also, the working time of the cleaner varies according to the complexity of the room, the volume of garbage, and the cleaning mode, and the cleaner work speed and time is different for wooden floors, ceramic tiles, and other flat ground.
T
Tina WilliamsAug 28, 2025
How to fix roller brush error on Onson Vacuum Cleaner?
- D
  David JonesAug 28, 2025
  To fix a roller brush error on your Onson Vacuum Cleaner, check if the roller brush is entangled and clean the roller brush.
K
Kathleen ChaneyAug 30, 2025
How to fix side brushes error on Onson J10C?
- B
  Benjamin WardAug 30, 2025
  To fix a side brushes error on your Onson Vacuum Cleaner, check if the side brush is blocked and clean the side brush.
J
jpattersonSep 1, 2025
How to fix fan error on Onson J10C?
- B
  brendadavisSep 1, 2025
  To fix a fan error on your Onson Vacuum Cleaner, clean up the garbage and air ducts channel.
Y
Yvonne GonzalezSep 4, 2025
How to resolve driving wheel error on Onson J10C?
- A
  Amanda GordonSep 4, 2025
  To resolve a driving wheel error on your Onson Vacuum Cleaner, check if the drive wheel is blocked.
D
Danielle ClarkSep 7, 2025
What to do if Onson Vacuum Cleaner shows low power or charging error?
- N
  nicholasbullockSep 7, 2025
  If your Onson Vacuum Cleaner shows a low power or charging error because the robot voltage is too low, it needs manually charging.
B
boltonmichaelSep 9, 2025
What to do if Onson J10C shows drop sensor error?
- M
  Mary JimenezSep 9, 2025
  If your Onson Vacuum Cleaner is showing a drop sensor error, check if the bumper is dirty and clean the sensor.