Optex Inc. - 1845 W 205th St. - Torrance, Ca. 90501 - 800-966-7839 SMDC-16 Program Manual 3440-0252 A4
4. System Options4. System Options
4.5. Emergency (continued)4.5. Emergency (continued)
4.5.4 Bell 2
BELL OUTPUT 2
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate Bell 2 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.5.5 Relay 1
RELAY OUTPUT 1
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate Relay 1 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.5.6 Relay 2
RELAY OUTPUT 2
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate Relay 2 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.5.7 PGM 1
PGM OUTPUT 1
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate PGM 1 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.5.8 PGM 2
PGM OUTPUT 2
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate PGM 2 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.5.9 PGM 3
PGM OUTPUT 3
NO 0=NO 1=YES
Selections: Yes / No
Default: No
Enable this option to activate PGM 3 output when the Emergency keys have been activated.
(see 2.2.1-Cutoff Times / 4.5.1-Emergency Enable).
4.6. Two Wire Smoke4.6. Two Wire Smoke
This section determines the characteristics of the 2 wire smoke detector The maximum
number of 2 wire smoke detectors connected to this loop may not exceed 10 for UL
installations. Please refer to the SMDC Hookup Diagram for the compatibility listing
of 2 wire smoke detectors.
4.6.1 Alarm Report Code
ALARM RPT CODE
code NO
Selections: 01-FF / Contact ID / SIA
Default: No Report
Select the report code that will be transmitted to the central station when an alarm condition
is sensed on the 2 wire smoke detector circuit. (see wiring diagram / 3.8.3-Rcvr Routing /
SIA-Contact ID-Hex charts on pg 42 & 43).
1. Monitor Mode
1. Ack Required
2. Scroll Open Zones
3. Scroll Bypass
4. Silent Mon. Mode
5. Auto Mon on Disarm
6. PIN Entry Required
7. Outputs
1. Bell 1
2. Bell 2
3. Relay 1
4. Relay 2
5. PGM 1
6. PGM 2
7. PGM 3
2. Walk Test Mode
1. Bell 1
2. Bell 2
3. Relay 1
4. Relay 2
5. PGM 1
6. PGM 2
7. PGM 3
3. System Features
1. Hist. View by User
2. O/C View by User
3. Silent Trouble
4. Not Used - Reserved
5. 50Hz/60Hz
6. AC/Crystal
7. Pwr Dly Time
8. PIN Require for Scan
9. Threshold Bad Codes
4. System Messages
1. Top Line Display
1. Grp/Part 1 Display
7-8. Group/Part Display
2. Disarmed Nml Msg
3. Disarmed Abnml Msg
5. Emergency
1. Emergency Enabled
2. Emergency Rpt
3. Bell 1 Output
4. Bell 2 Output
5. Relay 1 Output
6. Relay 2 Output
7. PGM 1 Output
8. PGM 2 Output
9. PGM 3 Output
6. 2 Wire Smk
1. Alarm Report
2. Trouble Report
3. Smoke Restore
4. Smoke Reset
5. Alarm Verify
6. Outputs
1. Bell 1 Output
2. Bell 1 Pulse
3. Bell 2 Output
4. Bell 2 Pulse
5. Relay 1 Output
6. Relay 2 Output
7. PGM 1 Output
8. PGM 2 Output
9. PGM 3 Output
7. Force Arming Enabled
8. PGM / INP Functions
1. PGM 1 Function
2. PGM 2 Function
3. PGM 3 Function
To Next Page
Loading...
Need help?
General