What to do if loudness drops momentarily during HD Radio analog/digital crossfades in Orban Computer Hardware?
If you experience loudness drops momentarily during HD Radio analog/digital crossfades with your Orban Computer Hardware, it might be because the analog and digital channels in your transmission path have reversed polarity with respect to each other. You can correct this with the HD POLARITY or FM POLARITY controls.
How to fix harsh sibilance (“Ess” Sounds) in the HD Channel of Orban OPTIMOD-FM 5700i Computer Hardware?
If you notice harsh sibilance (“Ess” Sounds) in the HD Channel of your Orban Computer Hardware, adjust the HD DE-ESS control and/or activate the HD channel’s band 5 compressor.
How to adjust the HD output if it sounds too bright in Orban Computer Hardware?
If the HD output of your Orban Computer Hardware sounds too bright, enable adjustment of the HD output’s spectral balance by putting the on-air preset into INDEPENDENT mode.
What to do if talent complains about delay in their headphones with Orban OPTIMOD-FM 5700i Computer Hardware?
If talent complains about delay in their headphones when using Orban Computer Hardware, dedicate an output to low-delay Monitor mode and use this to drive headphones.
Why does audio mute occur when switching between UL and Non-UL Presets in Orban Computer Hardware?
This is normal for Orban Computer Hardware. The audio mute occurs when switching between UL and Non-UL Presets because the DSP code must be reloaded.
What to do if the 19 kHz Frequency is Out-of-Tolerance in Orban Computer Hardware?
First, verify that a problem really exists by using a second frequency-measuring device and/or verifying the problem with a monitoring service.
What to do if the system receiving Orban 5700i’s Digital Output Will Not Lock?
If the system receiving your Orban 5700i’s digital output will not lock, ensure that the 5700i’s output sample rate is set to match the sample rate that the driven system expects. Also, ensure that the 5700i’s output FORMAT (AES3 or SPDIF) is set to match the standard expected by the driven system.
Why does Orban Computer Hardware sound dull?
If you are using the Two-Band structure, dull-sounding source material will sound dull on the air. The Five-Band structure will automatically re-equalize such dull-sounding program material to make its spectral balance more consistent with other program material.
Why is there a whistle on air, perhaps only in stereo reception, with Orban OPTIMOD-FM 5700i?
The most likely cause of a whistle on air, perhaps only in stereo reception, when using Orban Computer Hardware is oscillation in the analog input or output circuitry. Check the analog or digital outputs with a spectrum analyzer to see if the spurious tone can be detected here.
Why is there audible noise on air with Orban OPTIMOD-FM 5700i?
Excessive compression will always exaggerate noise in the source material. The compressor gate freezes the gain of the AGC and compressor systems whenever the input noise drops below a level set by the threshold control for the processing section in question.
Manual structure, navigation, and search features.
Overview of the processor's capabilities, benefits, and advanced features.
Describes the front panel controls, LCD, and LEDs for easy operation.
Details the unit's advanced peak control and transmitter protection for FM broadcast.
Highlights the unit's adaptability with multiple input/output options and processing structures.
Details the various analog and digital input/output options available.
Step-by-step guide for unpacking, mounting, and connecting the unit.
Guided setup process for basic configuration.
Detailed setup for analog and digital input/output parameters.
Instructions for connecting to a PC for remote control and software updates.
Guidance on proper grounding techniques for optimal performance.
Overview of front panel controls, display, and buttons.
Explanation of input, gain reduction, composite, and multiplex power meters.
Fundamental concepts of audio processing.
Guides on adjusting presets for desired station sound.
Lists and describes factory presets for various formats.
Common issues and their resolutions.
Addresses potential interference and noise issues.
Troubleshooting steps for inadequate peak modulation control.
Common problems encountered when connecting the unit to a PC.
Presents technical specifications for various parameters.
Details frequency response, noise, distortion, and separation specs.
Detailed breakdown of the unit's internal circuitry and sections.
Description of the microprocessor-based control system.
General| Brand | Orban |
|---|---|
| Model | OPTIMOD-FM 5700i |
| Category | Computer Hardware |
| Language | English |
To Next Page
