Ozito OBD2 - BATTERY TESTER SAFETY WARNINGS; WARNING! Save all warnings and instructions for future reference; MAINTENANCE; CARING FOR THE ENVIRONMENT

Regulatory Compliance Mark
(RCM)
Warning
V
Volts
A
Amperes
Read Instruction Manual
A
MAINTENANCE
DESCRIPTION OF SYMBOLS
Cleaning
• We recommend that you clean the device immediately each time
you have finished using it.
• Keep the OBD2 automotive Scan tool dry, clean and free from oil,
water and grease.
• Clean the appliance regularly with a cloth. Do not use cleaning
agents or solvents; these may be aggressive to the plastic parts
in the appliance. Ensure that no water can get into the interior of
the appliance.
Storage
• The automotive scan tool should be placed in a dry room for
storage.
Note: Ozito Industries will not be responsible for any damage or
injuries caused by the repair of the tool by an unauthorised person
or by mishandling of the tool.
WARNING! BEFORE CLEANING THE APPLIANCE MAKE
SURE THAT IT IS DISCONNECTED FROM THE VEHICLE.
Power tools that are no longer usable should not
be disposed of with household waste but in an
environmentally friendly way. Please recycle where
facilities exist. Check with your local council authority for
recycling advice.
Recycling packaging reduces the need for landfill and
raw materials. Reuse of recycled material decreases
pollution in the environment. Please recycle packaging
where facilities exist. Check with your local council
authority for recycling advice.
CARING FOR THE ENVIRONMENT
SPARE PARTS
Spare parts can be ordered from the Special Orders Desk at your
local Bunnings Warehouse.
For further information visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: enquiries@ozito.com.au
BATTERY TESTER SAFETY WARNINGS
WARNING! Save all warnings and instructions for future reference
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
- This appliance is not intended for use by young or infirm persons unless supervised by a responsible
person to ensure that they can use the appliance safely.
- Young children should be supervised to ensure that they do not play with the appliance.
- The warnings, cautions and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
- Common sense and caution are factors that cannot be built into this product but must be supplied
by the operator.
- Wear safety eye protection that meets AS/NZS standards.
- Always perform automotive testing in a safe environment.
- Keep clothing, hair, hands, tools, test equipment, etc away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
- Operate in a safe work environment. Keep your work area clean and well lit.
- Always lock up tools and keep them out of the reach of children.
- Do not expose OBD2 automotive Scan tool to rain, snow or wet conditions.
- Keep the OBD2 automotive Scan tool dry, clean and free from oil, water and grease.
- Stay clear of hot engine and car parts.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Use this product in accordance with these instructions, taking into account the working conditions
and the work to be performed. Use of this product for operations different from those intended could
result in a hazardous situation.
- This product is not a toy. Keep it out of reach of children.
- Maintain labels and nameplates on the unit. These carry important safety information.
- Don’t connect or disconnect any test equipment with ignition on or engine running.
- Ensure automatic vehicles are in park with the handbrake engaged before starting the engine.
- Ensure manual vehicles are in neutral with the handbrake engaged before starting the engine.
- Put blocks on drive wheels and never leave car unattended while running tests.
- Road Safety Road Rules 2009 penalty code 2135, it is illegal to leave “motor vehicle unattended with
keys in ignition, motor running, brakes not secured or doors unlocked.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark
plugs. These components create hazardous voltages when the engine is running.
- This battery tester was designed for specific functions. Do not modify, disassemble or alter the
battery tester, all parts and accessories are designed with built-in safety features that may be
compromised if altered.
- Do not use the battery tester in a way for which it is not designed.