Stinger HEIGH10
®
Installation & Integration Kit
for 2011-2018 Jeep
®
Wrangler JK
SRK-JK11HX
© 2024 Stinger
Stinger Solutions is not aliated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC. The
terms OEM, Jeep®, Wrangler®, and Gladiator® all terms are used strictly for identication purposes only. It is
not implied that any part listed is a product of, or approved by, Fiat Chrysler Automobiles.
Pacific Accessory Corporation
Page 1
Rev: V3
Date:072924
®
Introduction and Features
The SRK-JK11HX is a complete radio installation kit for 2011-2018 Jeep Wrangler JK and the Stinger HEIGH10 Infotainment
system (sold separately). All modules and cables are included to retain important features of the factory system, including: steering
wheel-mounted radio controls, USB port, factory amplier and AM/FM reception. Data integration with the vehicle and the Stinger
HEIGH10 adds advanced vehicle information, performance gauges, o-road enhancements, four programmable camera triggers,
and factory amplier control. Plug & Play wiring harnesses, along with a “zero-modify” mounting system, allow for a quick and easy
installation without the need to cut or splice any factory wiring or modifying the vehicle trim panels or sub-dash.
Important Notes
Recommended Tools
We recommend reading this manual thoroughly to familiarize yourself with the entire process prior to
beginning the installation. Although this kit does not require any modications to the vehicle, it does
require following the steps as shown to ensure it is installed correctly with no damage to the vehicle.
1. Mounting Panel Front Frame
2. HEIGH10, Horizon10 Display Mounting Panel
3. UN1810 Harness (SR-SRK-ADAPT-UN1810 V1)
4. IX210 Harness (SR-SRK-ADAPT-IX2XX V1)
5. Main Harness (SRK-CH1A-HAR V2)
6. Side Mounting Brackets (x2)
7. Top Support Bracket
8. 18” USB Adapter (USB-UN3)
9. Module Bracket (H_MODULE_BRKT)
10. PAC-LINK/Speed Sen Harness (10P-2-10P-6-HAR)
11. 2014-2018 CAN Harness (JK14-CAN-HAR)
12. 2011-2013 CAN Harness (JK07-CAN-HAR)
13. Satellite Antenna Adapter (SAT-01)
14. AM / FM Antenna Adapter (BAA22)
15. PAC-LINK Module (PL1)
16. Radio Replacement Interface Module (CH1A-SRK)
17. USB-A / USB-C Extension (SSUSB3)
18. USB-C TO USB-A Adapter included with (SSUSB3)
1
16
17
18
15
14
13
11
9
6
2
3
4
5
7
8
10
12
Included Components
1. Does not retain the following factory features:
● Uconnect
®
● SiriusXM
®
Satellite Radio
2. To retain SiriusXM Satellite Radio would require purchasing a SXV300 SiriusXM tuner.
3. Directions for removing the HEIGH10 display panel are on page 17.
Plastic Panel Tool
7mm, 10mm Socket
Ratchet
#2 Phillips Screwdriver
Pick Tool
Flush Cutters
Wire Feeder
Cloth Tape
Painters Tape
NOTE: There is a component list, hardware
guide, wire harness descriptions and illustrations
in the HEIGH10 (UN1810) Installation Guide for
reference.
Included zip ties, M4 x 10 Screws (4x), clip nut and #10-24 X ½” screw not shown.
To Next Page
Need help?
General
