To Next PageTo Next PageWhat to do if Pacific hydrostar SUBMERSIBLE DIRTY 93819 has insufficient flow?
To resolve insufficient flow in your Pacific hydrostar Water Pump, start by cleaning the Impeller and Impeller Cover. Also, inspect the Discharge Pipe for any freezing or blockages, and thaw the pipe or remove any debris if necessary. If the issue persists, have a qualified technician clean the interior of the pump and replace any worn parts.
How to fix Pacific hydrostar SUBMERSIBLE DIRTY 93819 Water Pump that does not start?
If your Pacific hydrostar Water Pump isn't starting, ensure it's properly plugged into a working 120 volt, GFCI, electrical outlet. Also, adjust the Float Switch to a lower position.
What to do if there is no flow from Pacific hydrostar SUBMERSIBLE DIRTY 93819?
If there's no flow from your Pacific hydrostar Water Pump, begin by cleaning the Impeller and Impeller Cover. Then, check the Discharge Pipe for any freezing or blockage, and thaw the pipe or remove debris if needed. Also, make sure the Discharge Pipe isn't excessively bent; if it is, reset the pipe.
Why does Pacific hydrostar SUBMERSIBLE DIRTY 93819 switch off too soon?
If your Pacific hydrostar Water Pump switches off too soon, start by cleaning the Impeller and Impeller Cover. Also, ensure that the water temperature does not exceed 95° Fahrenheit.
What to do if Pacific hydrostar SUBMERSIBLE DIRTY 93819 Water Pump does not switch off?
If your Pacific hydrostar Water Pump does not switch off, it may be because the Float Switch cannot sink down. Try lowering the Float Switch.
General| Brand | Pacific hydrostar |
|---|---|
| Model | SUBMERSIBLE DIRTY WATER PUMP 93819 |
| Category | Water Pump |
| Language | English |
Identifies the two available models of the submersible pump.
Instructions for assembling and operating the pump.
Crucial safety directive to read all warnings and instructions before operating.
Details on voltage, frequency, wattage, and amperage for each model.
Specifies the plug type as 3-Prong, Grounded.
The maximum diameter of particles the pump can handle.
The volume of water the pump can move per hour/minute.
The maximum vertical distance the pump can push water.
Explains the manual's purpose and contents for future reference.
Emphasizes the importance of reading and understanding all instructions.
Guidance on maintaining a clean and well-lit work area.
Warning against using the pump in areas with flammable liquids, gases, or dust.
Advises keeping others at a safe distance during operation.
Mandates using GFCI outlets for grounded tools and proper grounding.
Explains polarized plugs for double-insulated tools.
Warning about increased shock risk when in contact with grounded surfaces.
Instructions on proper handling and care of the power cord.
Advises operators to remain alert and use common sense while operating.
Safety precautions regarding clothing and jewelry near moving parts.
Recommends wearing safety goggles and appropriate footwear.
Safety measure to disconnect power before any adjustments or storage.
Guidelines for safely storing equipment out of reach of unauthorized persons.
Pre-use checks for parts alignment, binding, or damage.
States that service should only be done by qualified technicians.
Emphasizes using identical replacement parts for servicing.
Importance of keeping labels legible for essential information.
Recommends safety goggles for assembly to prevent injury.
Advises using the product only for its intended applications.
Importance of a well-lit and clear environment for safe operation.
Crucial warning to disconnect power before handling or adjusting the pump.
Prohibits pumping flammable, explosive, or corrosive materials.
Ensures the discharge pipe is secured for pump stability.
Requirement for stable operation by placing the pump on a level surface.
Safety instruction to create a drip loop in the power cord to prevent water ingress.
Recommends professional installation of a dedicated GFCI outlet.
Warning against lifting or lowering the pump using its power cord.
Instructions for winterizing the pump to prevent freeze damage.
Advise to periodically check and tighten all connections.
Caution for individuals with pacemakers regarding electrical equipment proximity.
Acknowledges limitations of the manual and emphasizes operator caution.
Critical warning about the dangers of improper grounding.
Explains the function and requirements for grounded tools with 3-prong plugs.
Details how the grounding prong connects to the tool's grounding system.
Requirement for using properly installed and grounded outlets.
Describes double-insulated tools and their lack of grounding requirement.
States that double-insulated tools can use standard 120V outlets.
Definition of the Double Insulated symbol.
Identification of the Canadian Standards Association mark.
Identification of the Underwriters Laboratories, Inc. mark.
Definition of the Volts Alternating Current symbol.
Definition of the Amperes symbol.
Definition of the No Load Revolutions per Minute symbol.
Instructions to verify all parts are present upon unpacking.
Safety instruction to disconnect power before assembly or adjustments.
Recommends professional installation of a dedicated GFCI outlet.
Specifies the discharge outlet size and compatible pipe diameter.
Instructions for connecting the union to the coupler and tightening.
Suggests installing a union for easier discharge pipe removal.
Recommends a check valve to prevent backflow and mentions air bleed hole.
Guidance on properly placing the pump without damaging cords or pipes.
Explains the automatic operation of the float switch based on water depth.
Informs about the motor's built-in thermal protector and its function.
Instructions for connecting discharge pipes to route water to the desired location.
Critical information on not exceeding the pump's maximum lift capacity.
Step to connect the pump's power cord to the GFCI outlet.
Describes the automatic activation of the pump based on water level.
Critical safety procedure for shutting off power to the pump.
Reiterates safety to disconnect power before any maintenance.
Advises pre-use inspection for damage, leaks, or blockages.
Instructions for cleaning the impeller cover and impeller to maintain performance.
Steps to disassemble the pump base to access and clean the impeller.
Guidelines for storing the pump safely when not in use.
Caution to use qualified technicians for unmentioned maintenance or repairs.
Common issues and solutions when the pump fails to start.
Steps to take when the pump is not moving water.
Solutions for when the pump fails to turn off automatically.
Causes and fixes for reduced water flow from the pump.
Reasons and solutions for the pump shutting off prematurely.
Clarification that some parts are for illustration only and not individually available.
Note about parts shown for illustration and availability.
Statement of commitment to product quality and durability.
Lists exclusions from warranty coverage, such as misuse or lack of maintenance.
Procedure for returning products or parts for warranty claims.
Informs users about their legal rights under the warranty, which may vary by state.
