9
This
screen
should
appear.
Select
a
number
1 .
Restore
the
whole HOD to factory default
2.
Restore
Windows(R) 2000 Professional to the first partition
3. End
Select
a
numt)er
1.
Restore
the whole HDD to factory
default
2.
Restore
Windows(R)
XP Professional
to
the first partition
3.
End
10
Make a
selection from the menu.
To
restore
all contents of the hard disk
to
factory de-
fault,
including
the partition
setting($):
Select
[1
.
Restore
the whole HDD to factory default].
To
reinstall
Windows 2000/Windows
XP to the first par-
tition
to
factory default:
Select
[2.
Restore
Windows(R)
2000 Professional (or
Windows(R)
XP
Professional)
to the
first partition].
In
such
cases, the initial partition size must be 6
GB or
more
of the hard disk size. Reinstallation
cannot be
performed with a small partition size.
1 1
At
the
confirmation message, press
C
Y
]
.
The
computer
will reboot, and the operations of reinstal-
lation
for the
hard disk start automatically. (The opera-
tions take
about
30-40
minutes.)
When
the message "insert the next
CD"
is displayed, insert
the
Product
Recovery
CD-ROM showing the next number
in
the
sequence,
and
then
select [OK].
(In
the case of
Windows
2000,
only Product Recovery
CD-
ROMs 1
to
3
can
be used.)
Xnote>
If the message "The media does not contain
the correct
file"
appears, select
[OK].
The
message
"insert the next
CD"
will
be displayed again.
Confirm that the proper Product Recovery
CD-ROM
has
been
inserted by opening the tray of the
CD
drive
and
then close the tray, then select
[OK].
12
After the reinstallation
procedure
completes,
press
C
Enter
)
. The
computer
will be shut
down.
<Only
when using the CD drive
Panasonic
KXL-
RW10A>
Remove
the
FIRSTAID
FD.
13
Remove
the
CD
drive,
and then turn the
computer
on.
14
When the
message [Press
F2
to
enter SETUP]
is
displayed,
press ( F2 ]
and
then run the Setup
Utility.
If the
password has
been set, enter
the
Supervisor
Pass-
word.
f5
Press
Cfd)
.
At
the co nfirmation
message,
select
[Yes] and
press
(
Enter
3
.
(The
Setup
Utility
settings will
return
to their
default
values.
Even
the
security
settings with the
excep-
tion
of the
password(s)
will
return to
their default
values.)
Change the
settings
where
necessary.
76
Press
CeTD
At the
confirmation
message, select
[Yes] and press
(Enter) .
7 7
Perform the setup
procedure for
Windows
by following
the
instructions
on the
screen.
(Q^
page
1
1)
note}-
When
the
FIRSTAID
FD
is
to
be created, follow the
steps in the
readme.txt
on
the disk.
((^
page 1
2)
iWinclowsF200'0l
<When using
a PC
Card-compatible
CD
drive
other
than
the Panasonic
KXL-RW10A>
Copy
the necessary drivers,
from the floppy
disk included
with
your
CD
drive,
to the
FIRSTAID FD with
the method
below.
It
will
be
necessary
to edit
the CONFIG.SYS file
and
AUTOEXEC.BAT
file on the
FIRSTAID
FD.
When
editing the
AUTOEXEC.BAT
file,
some
CD
drives
require
card managers (card
and
socket service).
See the
manual
included with your
CD drive
for further
details.
®
Start
Window
s and insert the
FIRSTAID
FD.
Select
[Start]
-
[Programs]
-
[Acces-
sories]
-
[Notepad]
-
[File]
-
[Open],
input
[a:\config.sys],
then select
[Open].
Select [start]
-
[All Programs]
-
[Ac-
cessories]
-
[Notepad]
-
[File]
-
[Open],
input
[a:\config.sys], then
select
[Open].
Rewrite
the
following
line and save.
Delete the
following
four lines.
;KXL-RW10A
DRIVER
DEVICE=A:\TOOLS\KMASMGRA.SYS
DEVICE=A:\TO0LS\KMASASPA.SYS
DEVICE=A:\TOOLS\KMASCDA.SYS
/D:MSCD0OO
Add the
driver
of your CD drive.
Device=A:
\pRlVHRl.SYS
/D:MSCDOOO
'-Rewrite
this
driver
for
the driver
of your
CD
drive.
The driver
for the PC Card will
also be necessary.
Refer to the operation
manual
that accompanies
the
CD
drive.
Save
the file
and
close [Notepad],
(?)
Copy the CD driver file (i.e.,
the driver
file rewritten in
step
©)
of
the
CD-ROM
drive
below
[a:\] of the
FIRSTAID
FD.
©
Set the floppy
disk
to the write-protect
stale.
After this,
follow
the
reinstalling
procedure
of
<Oiily when
using
the CD drive
Panasonic KXL-RW10A>.
(Q-
page
24)
25
To Next Page
Loading...
Need help?
General