Panasonic CQ-C1120U - Unit Operation and Controls; Power, Volume, and Mute Functions; Display and Audio Settings; Clock Setting and Adjustment

POWER
CLOCK
CQ-C1200U
DISP
SQ
MUTE
789101112SCAN
1
2
3
46
APM
BA
N
D
SRC
5
V
O
L
U
M
E
/
P
U
S
H
S
E
L
REP
TUNE
TRACK
D
•
M
POWER
CLOCK
CQ-C1200U
DISP
SQ
MUTE
789101112SCAN
1
2
3
46
APM
BAND
SRC
5
V
O
L
U
M
E
/
P
U
S
H
S
E
L
REP
TUNE
TRACK
D
•
M
1
E
N
G
L
I
S
H
13
CQ-C1200U/C1120U/C1110U/C1100U
1
E
N
G
L
I
S
H
2
12
CQ-C1200U/C1120U/C1110U/C1100U
Hours
w
Press and hold [DISP] (clock) for more than 2
seconds.
e Press [k TUNE] or [l TUNE].
Minutes
r
Press [DISP] (clock).
t Press [k TUNE] or [l TUNE].
y Press [DISP] (clock).
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
Audio Mode
(Bass/Treble/Balance/Fader/Sub Woofer)
Regular mode
Volume
Bass Treble
BalanceSub Woofer
Fader
Note: If no operation takes place for more than 5 sec-
onds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.
Bass:
Adjustable range: –12 to +12 (by 2 dB step)
Treble:
Adjustable range: –12 to +12 (by 2 dB step)
Balance:
R (right speaker) or L (left speaker)
Fader:
F (front speaker) or R (rear speaker)
Push [SEL] to select the audio mode.
q
Clock Setting
The 12-hour system is used for the clock.
(Hours blink.)
(Hours set.)
(Minutes blink.)
(Minutes set.)
(End.)
Initial Time
q Press [DISP] (clock).
"AdJ" is displayed when the clock is not
adjusted.
Time Reset
Press and hold [DISP] (clock) for more than
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.
[DISP] (clock)
[k TUNE], [l TUNE] (Hours, minutes)
Adjustable range: 1 to 15 (by 1 step) Balance center
Adjustable range: 1 to 15 (by 1 step) Fader center
(Only for CQ-C1200U)
Sub Woofer:
Adjustable range (level): MUTE (0) to 7
(Only for CQ-C1200U)
Push
Turn [VOLUME] clockwise or counterclockwise
to change each level.
w
default: 0 dB
default: 0 dB
(default)
(default)
default: 4
D
ISP
SQ
MUTE
SRC
Power and Sound Controls
Mute
Press [MUTE] to mute the sound completely.
lights
Press [MUTE] again to cancel.
Volume
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
Volume level (0 to 40)
(default: 18)
SQ (Sound Quality)
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
Press [SQ] to select a sound type as follows:
(default)
SQ -- (default) flat frequency response:
does not emphasize.
SQ - 1 (ROCK) speedy and heavy sound:
exaggerates bass and treble.
SQ - 2 (POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
SQ - 3 (VOCAL) clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Power
Turn the key in the ignition until
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off: Press [SRC](POWER)
again and hold.
ACC
ON
MUTE
ST
Display Change
Press [DISP] (display) to switch to the clock display.
Note: "AdJ" is displayed when the clock is not adjusted.
(
➡ page 13)
When the power is off:
No display Clock display
Remote control sensor (➡ page 18)*
(only for CQ-C1200U/C1120U/C1110U)
Up
Down
SQ indicator
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
•
Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,
readjust bass/treble or volume (➡ page 13).
• CQ-C1100U has no remote control function.*