Panasonic DMR-EZ485VK

12
RQT9056
Setting the Channels and Clock
POWER
DVD/VHS
to turn the unit on.
“HELLO” appears on the unit’s display.
When this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 3 via an HDMI cable ( 11),
it acquires the setting information from the TV. When the
Quick Start Setting screen appears ( 14, Step 1)
When this unit is connected to a TV via an HDMI cable, this step is not required.
TRACKING/V-LOCK
CH
to select an RF output channel number.
 Connection (without HDMI cable or Audio/Video cable): While
viewing the unit’s front display, select “CH3” or “CH4”. If the
selection is appropriate, then the step 3 screen will appear.
 Connection (with Audio/Video cable): While viewing the
unit’s front display, select “OFF”.
Select Language
Seleccione el idioma
Sélection de langue
Press OK
English
Français
Español
Language:
,  to select, then
OK
When the Quick Start Setting screen
appears after this step ( 14, Step 1)
Select TV type and press OK.
(Please refer to Operation Instruction
for details)
Aspect Ratio Selection
4:3 TV
16:9 Widescreen TV
TV Aspect Ratio:
,  to select “4:3 TV” or “16:9
Widescreen TV”, then
OK
 When connecting to a 4:3 standard aspect TV:
Select “4:3 TV”.
 When connecting to a 16:9 widescreen TV:
Select “16:9 Widescreen TV”.
The unit can be turned on faster, in about
1 second. Please note that Quick Start
mode slightly increases power
consumption when the unit is off.
(See Operation Instructions for details)
Turn Quick Start on ?
On
Off
Quick Start Setting
Quick Start Function:
,  to select “On” or “Off”,
then
OK
Does this unit get its TV signal via RF IN?
Example: Antenna, Cable TV or Cable Box connected to the
unit’s RF IN.
Yes
No
Automatic Clock and Channel Settings
Automatic Clock and
Channel Settings:
,  to select “Yes” or
“No”, then
OK
 When connecting the cable from the wall (cable TV or
antenna) to the unit’s RF IN:Select “Yes”.
The unit then displays the source selection screen ( 13).
 When not connecting the cable from the wall (cable TV or
antenna) to the unit’s RF IN:Select “No”.
The unit then displays “Set Clock Manually” screen ( 13,
Manual Clock Setting).
Tips
 “Quick Start” function ( 58)
If you set Quick Start to on, you
can start recording to DVD-RAM
about 1 second after you press
[ DVD/VHS POWER] to turn the
unit on and then sequentially press
[ REC].
The following happens when you have
selected “On”.
– Power consumption in standby mode
increases because power is supplied
to the unit.
To return to the previous screen
Press [RETURN].
Preparation:
 Turn on the TV and select the appropriate video input
to suit the connections to the unit. (Example: AV
input, CH3 or CH4)
 These are the first settings you make upon buying
the unit. You don’t need to make these settings again.
POWER
POWER
SLOW/SEARCH
S
C
H
E
D
U
L
E
OK
F
U
N
C
T
I
O
N
S
TV/VIDEO
PAU S E
STOP
3
2
1
6
5
4
9
8
7
0
REC MODE
RETURN
SUB MENU
CM SKIP
D
I
R
E
C
T
N
A
V
A
I
G
A
T
A
A
O
R
DISPLAY
AUDIO
REC
DRIVE
SELECT
F Rec
STATUS
CHAPTER
CREATE
INPUT SELECT
DELETE
FAVORITE
CH
CH
PLAY
VOL
A
B
DVD/VHS
VCR/TV
TRACKING/V-LOCK
SKIP
/
INDE
X
REW
FF
TIME SLIP
/
/
JET REW
RESET









DMR-EZ48VP.indb12DMR-EZ48VP.indb12 2007/12/1320:42:292007/12/1320:42:29