ENGLISH
119 (E)
Video Output Connector
Analogue component output: BNC × 3 (Y, P
B, PR)
Y; 1.0 Vp-p, 75Ω
P
B/PR; 0.7 Vp-p, 75Ω (100% colour bar, 0% black level)
Analogue composite output: BNC × 3, video 1, video 2 (video/WFM selectable), video 3 (superimpose on/off)
Serial digital component output: BNC × 3, complies with SMPTE 259M-C/EBU Tech.3267-E standard, SDI 1, SDI 2, SDI 3,
(superimpose on/off)
SDTI output (option): BNC × 1, complies with SMPTE 305M/321M standard (also serves as SDI1 output
connector)
Video Signal Adjustment
Composite video input signal: ±3 dB
Video output gain: ±3 dB
Video output chroma gain: ±3 dB
Video output chroma phase: ±30°
Video output black level: ±100 mV
Video output sync phase: ±15 µsec
Video output SC phase: ±180°
AUDIO
Digital Audio
Sampling frequencies: 48 kHz (synchronous with video)
Quantizing: 16 bits
Frequency response: 20 Hz to 20 kHz ± 1.0 dB (at the reference level)
Dynamic range: Better than 90 dB (1 kHz, emphasis OFF, “A” weighted)
Distortion: Less than 0.05% (1 kHz, emphasis OFF, reference level)
Crosstalk: Less than –80 dB (1 kHz, between 2 channels)
Wow & flutter: Below measurable limit
Headroom: 625i; 18 dB
525i; 20 dB
Emphasis: T1 = 50 µsec, T2 = 15 µsec (on/off selectable)
Cue Track
Frequency response: 300 Hz to 6 kHz ± 3.0 dB
Audio Input Connector
Analogue input
(CH1/CH2/CH3/CH4): XLR × 4, 600Ω/high impedance selectable (factory setting: 600Ω),
+4/0/–20 dBm selectable*
Digital input (CH1/CH2, CH3/CH4): XLR × 2, AES/EBU format
Serial digital input: Complies with SMPTE 259M-C, 272M/EBU Tech.3267-E (BNC × 1, 75Ω)
Cue track input: XLR × 1, 600Ω/high impedance selectable (factory setting: 600Ω),
+4/0/–20/–60 dBm selectable*
Audio Output Connector
Analogue output
(CH1/CH2/CH3/CH4): XLR × 4, low impedance, +4/0/–20 dBm selectable (with 600Ω load)*
Digital output
(CH1/CH2, CH3/CH4): XLR × 2, AES/EBU format
Serial digital output: Complies with SMPTE 259M-C, 272M-A/EBU Tech.3267-E (BNC × 1, 75Ω)
Cue track output: XLR × 1, low impedance, +4/0/–20 dBm selectable (with 600Ω load)*
Monitor output: XLR × 2, low impedance, +4/0/–20 dBm selectable (with 600Ω load)*
Headphones: Variable level, 6.5 mm, 8Ω
Other Input/Output Connectors
Time code input: XLR × 1, 0.5 to 8 Vp-p, 10 kΩ
Time code output: XLR × 1, low impedance, 2.0±0.5 Vp-p (with 600Ω load)
RS-422A input: D-sub 9-pin, RS-422A interface
RS-422A output: D-sub 9-pin, RS-422A interface
RS-232C: D-sub 25-pin, RS-232C interface
Parallel input/output: D-sub 25-pin
Encoder remote: D-sub 15-pin
Weight and dimensions when shown are approxlmately.
Speclilcailons are subject to change without notice. * EG model is fixed to –3 dBu.
Specifications
To Next Page
Loading...
