Panasonic FX-501 Series

7
Pro4 menu items
<PRO5>
<PRO4>
SET
+, - +, -
+, -
+, -
SET +, -
SET
+, -
+, -
+, -
SET
+, -
+, -
SET
SET SET
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
SET
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
2 turns
Copy setting
Display
adjustment
Display copy
YES Good
Copy action
setting
Display
adjustment OFF
Automatic
Automatic
Copy lock OFF Copy lock ONCopy lock setting
Communication
mode
Communication
emission halt
Communication
protocol setting
Only displayed in FX-502□ or FX-505□-C2
External input
setting (note)
Emission OFF TeachingOnly one unit
Copy lock
Limit +
Display adjustment
Limit -
Logic setting
Data bank
load
Data bank
save
Emission OFF TeachingAll
Limit +
Display adjustment Limit -
Data bank
load
Data bank
save
* Use the following signal input times:
Purpose Signal input time
2‑point teaching
Limit teaching
Display adjustment
20 to <500ms
Full auto teaching ≥600ms (sampling during signal input)
Emission OFF, logic
setting, copy lock
≥2ms (function will be executed as long as the
signal is input)
Data bank loading
Data bank saving
Input the channel number by sending the
corresponding number of pulses (1 pulse: 16
to 300ms). Note that the time between pulses
should be at least 500ms.
Pro5 menu items
<PRO5>
<PRO6>
OFF
SET
+, - +, -
+, -
SET
+, -
SET
+, -
+, -
+, -
SET SET
+, -
+, -
+, -
SET
+, -
+, -
SET
+, -
+, -
SET
+,
-
SETSET
0
SET
-
SET
SET
+,
-
Display
adjustment setting
Target setting
(note)
Display
adjustment setting
Target setting
When you have seleted “Target setting”:
Save target value
Incident light
intensity
Code setting
Reset setting
CUSTOM setting
Response time
setting
Interference
prevention setting
Default
Different
frequency setting
Emission
frequency 1
Emission
frequency 2
Emission
frequency 3
Emission power
setting
Blink Blinks 3 times
Automatic
<RUN mode>
Hysteresis
setting
* The target setting for the display adjustment depends on the
selected response time.
Response time Incident light intensity
STD, H‑SP, FAST From ‑1,999 to 4,000
LONG From ‑1,999 to 8,000
U‑LG, HYPR From ‑1,999 to 9,999
Pro6 menu items
<PRO6>
(notes 1 and 2)
Normal mode
+, - +, - +, -
+, - +, -
SET
+, - +, -
+, -
+, -
Window
comparator mode
(only sensing
output 1)
Rising differential
mode (note 3)
Hysteresis
mode
Forced OFF
output mode
Forced ON
output mode
Falling differential
mode (note 3)
Only displayed in
FX-505□-C2
Only displayed in
FX-502□ or FX-505□-C2
SET
SET SET
SET
+, -
+, -
+, -
<PRO7>
+, -
Window comparator mode or hysteresis mode (the diagram below shows the
window comparator mode)
Shift amount
setting (in
percentage)
Shift amount setting
(note 5)
Answer back output
mode (only sensing
output 2, see note 4)
Self-diagnosis
output mode (only
sensing output 2)
* Notes
1. With FX-502□, you can select whether terminal 3 should be used as sensing
output 2 or as an external input. Activate sensing output 2 in Pro3 before making
settings in Pro6.
2. With FX-502□ or FX-505□-C2, you can switch between sensing output 1 or 2 by
pressing the MODE key until the display changes to the other output.