2.4.4. SERVICE FUNCTION TABLE
Code Function Set Value Effective Range Default Remarks
501 Setting the pause time 001~600 X 100 msec 001~600 05000 msec Selects the pause time in 100 msec steps.
502 Setting the flash recall time 01~99 X 10 msec 01~99 700 msec Selects the line break time during flashing in 10
msec steps.
503 Setting the pulse dial
speed
1:10pps 2:20pps 1, 2 10 pps Sets the pulse dial speed.
520 Setting the CED frequency 1:2100Hz 2:1100Hz 1, 2 2100 Hz When international communications cannot be
performed smoothly select 1100Hz. However
some exchange system should not be
accopted (1100Hz on CED). (See "5. Unit can
copy, but cannot transmit/receive long distance
or international communications" in 2.3.4.2.1
Defective facsimile section)
521 Setting the international
line mode
1:ON 2:OFF 1, 2 ON Selects the international line mode during FAX
communication. (See "5. Unit can copy, but
cannot transmit/receive long distance or
international communications" in
2.3.4.2.1 Defective facsimile section)
522 Setting the return to default
mode
1:ON 2:OFF 1, 2 ON Set the resolution and contrast conditions for
FAX or copy to the default settings.
523 Receive equalizer select 1:0km 2:1.8km
3:3.6km 4:7.2km
1~4 0km When the telephone station is far from the unit
or reception cannot be performed correctly,
adjust accordingly.
524 Transmissionequalizer
select
1:0km 2:1.8km
3:3.6km 4:7.2km
1~4 0km When the telephone station is far from the unit
or reception cannot be performed correctly,
adjust accordingly.
544 Selecting the document
feed position
01~99 step 00~99 50 When the ADF function is incorrect, adjust the
feed position. (8 step = 1mm)
550 Memory clear Press "START/COPY/SET".
551 ROM version and sum
check
Press "START/COPY/SET".
552 DTMF signal tone test 1:ON 2:OFF 1, 2 OFF Press "START/COPY/SET".
553 Setting the FAX monitor
function
1: OFF 2:PHASE B
3:ALL
1, 2, 3 OFF Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or
not.
554 Modem test Press "START/COPY/SET".
555 Scanner test Press "START/COPY/SET".
556 Motor test Press "START/COPY/SET".
557 LED test Press "START/COPY/SET".
558 LCD test Press "START/COPY/SET".
559 Setting the document jam
detection
1:ON 2:OFF 1, 2 ON Selects the jam detection of a document during
FAX transmission/copying.
560 Cutter selection 1:ON 2:OFF 1, 2 ON Turns OFF the cutter function.
561 KEY test Press any key.
562 Cutter test Press "START" key. [Refer to test function]
570 Setting the % break 1:61% 2:67% 1, 2 61% Sets the % break of pulse dialing.
571 Setting the number of
times that ITS is redialed
00~99 00~99 05 times Selects the number of times that ITS is redialed
(not including the first dial).
572 Setting the ITS redial
interval
001~999 sec 001~999 065 sec Sets the interval of ITS redialing.
573 Setting of number of rings
for REMOTE TURN ON
01~99 01~99 15 times Sets the number of rings before the unit starts
to receive a document in the TEL mode.
580 TAM continuous tone
detection
1:ON 2:OFF 1, 2 ON ON: Stops TAM operation when Dial tone, etc.
are detected.
590 Setting the number of FAX
redial times
00~99 00~99 5 times Selects the number of redial times during FAX
communication (not including the first dial).
591 Setting the FAX redial
interval
001~999 sec 001~999 065 sec Sets the FAX redial interval during FAX
communication.
592 Designation of CNG
sending
1: OFF 2:ALL 3:AUTO 1, 2, 3 ALL Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG is output only when automatic
dialing is performed. OFF: CNG is not output at
phase A.
593 Setting the interval
between CED and the 300
bps signal
1: 75 msec 2:500
msec 3:1000 msec
1, 2, 3 75 msec Sets the interval between the CED signal and
subsequent 300 bps signal. (See "5. Unit can
copy, but cannot transmit/receive long distance
or international communications" in 2.3.4.2.1
Defective facsimile section.)
77
KX-FT63BX / KX-FT63BX-W
To Next Page
Loading...
