To Next Page
S
Samantha NelsonAug 15, 2025
What to do if my Panasonic Telephone doesn't ring?
- JJoseph ValdezAug 16, 2025
If your Panasonic proprietary telephone isn't ringing, the ringer volume might be set to off. Adjust the ringer volume to 'HIGH' or 'LOW'.
What to do if my Panasonic Telephone doesn't ring?
If your Panasonic proprietary telephone isn't ringing, the ringer volume might be set to off. Adjust the ringer volume to 'HIGH' or 'LOW'.
How to troubleshoot a Panasonic Telephone extension that is not working?
If your Panasonic telephone extension isn't functioning, here are a few things to check: * Check the connection between the PBX and the telephone by plugging the telephone into the same extension port using a short telephone cord. If the telephone functions, then the connection between the PBX and the telephone must be repaired. * Plug the telephone into a known functioning extension port. If the telephone still doesn't function, replace the telephone, as it may be faulty. * If you're using a telephone with an A-A1 relay, use a 2-wire cord and set the A-A1 relay switch to the 'OUT' or 'OFF' position. * The extension card may be faulty. Exchange the card for a known functioning one.
Why can't I make outside calls with my Panasonic Telephone?
If you cannot make outside calls with your Panasonic PT, a flexible button on the PT may not be programmed to select an outside (CO) line. You need to program the CO buttons.
Why is there no sound when using the speakerphone on my Panasonic Telephone?
If you can't hear any sound when using the speakerphone on your Panasonic analog proprietary telephone, check the HANDSET/HEADSET selector. If it is set to the 'HEADSET' position, set it to the 'HANDSET' position when you are not using a headset.
Why can't my Panasonic SLT make calls in tone dialing mode?
If an SLT set to 'tone' dialing mode cannot make calls, there may be something wrong with the DTMF receiver. Select 'Enable' for DTMF receiver 1 and 'Disable' for DTMF receiver 2 through system programming, 'DTMF Receiver Check [107]'. Then try to make a call using a tone-type SLT connected to one of extension jacks 01– 08. If you still cannot make the call, the problem may have been caused by DTMF receiver 1. If the call can be made, try DTMF receiver 2. Select 'Disable' for DTMF receiver 1 and 'Enable' for DTMF receiver 2 through system programming, 'DTMF Receiver Check [107]', and make another call. If you cannot make the call, the problem may have been caused by DTMF receiver 2. Check the other 4 DTMF receivers the same way through 'DTMF Receiver Check [107]' in system programming.
How to fix Speed Dialing on my Panasonic Telephone?
If speed dialing or one-touch dialing is not working on your Panasonic telephone, ensure the outside (CO) line access number (e.g., 9, 0, or 81-88) is stored at the beginning of the telephone number. Incorrect programming can cause this issue.
What to do if Panasonic Proprietary telephones don't operate on extension jacks?
If proprietary telephones connected to extension jacks do not operate, but single line telephones do, the H and L pins of extension jacks may have shorted. Turn the Power Switch to the 'OFF' position. Fix the shorted part, then turn the Power Switch to the 'ON' position.
How to eliminate noise from Panasonic KX-TES824 Telephone external pager?
If you're hearing noise through the external pager (loudspeaker) connected to your Panasonic telephone system, and you are using an amplifier, the noise may be introduced through the cable connecting the PBX and the amplifier or loudspeaker. Try using a shielded cable to connect the PBX and the amplifier or loudspeaker. Using a shorter cable can also reduce noise.
What causes distorted audio on Panasonic Telephone?
If the audio (Music on Hold, Background Music) is distorted on your Panasonic telephone, the audio level from the output of the audio source might be too high. Try decreasing the output level of the external audio source by using the volume control on the audio source.
How to clear programming data on Panasonic PBX?
If the Panasonic PBX does not operate correctly after restarting, you can clear the programming data stored in the PBX: 1. Make sure that all outside (CO) lines you use are connected to the PBX. 2. Slide the System Clear Switch to the 'CLR' position. 3. Press the Reset Button, and then return System Clear Switch to the 'NOR' position before the power indicator stops flashing. (The power indicator will flash for about 5 seconds.)
General| RS-232 ports | 1 |
|---|---|
| RJ-11 ports quantity | 3 |
| Ethernet LAN (RJ-45) ports | 8 |
| Ethernet LAN | Yes |
| AC input voltage | 110 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 45 W |
| Product type | - |
| Product color | White |
| Number of simultaneous calls (max) | 2 |
Weight and Dimensions| Depth | 284 mm |
|---|---|
| Width | 368 mm |
| Height | 102 mm |
| Weight | 3500 g |
