Technical Information
ENGLISH - 103
Appendix
Mode
Resolution
(Dots)
Scanning frequency
Dot
clock
frequency
(MHz)
Picture
quality
*3
Plug and play
*6
Format
*7
Horizontal
(kHz)
Vertical
(Hz)
RGB2
DVI-D
EDID1
DVI-D
EDID2
MXGA
1
152 x 864 64.0 71.2 94.2 A
– – –
D/R
1
152 x 864 67.5 74.9 108.0 A
– – –
D/R
1
152 x 864 76.7 85.0 121.5 A
– – –
D/R
MAC21 1
152 x 870 68.7 75.1 100.0 A
3 – 3
D/R
1280 x 768
1
280 x 768 39.6 49.9 65.3 AA
*4
– – –
D/R
1
280 x 768 47.8 59.9 79.5 AA
*4
– – –
D/R
1280 x 800
1
280 x 800 41.3 50.0 68.0 AA
*4
– – –
D/R
1
280 x 800 49.7 59.8 83.5 AA
*4
– – –
D/R
MSXGA 1
280 x 960 60.0 60.0 108.0 A
– – –
D/R
SXGA
1
280 x 1
024 64.0 60.0 108.0 A
3 – 3
D/R
1
280 x 1
024 80.0 75.0 135.0 A
3 – 3
D/R
1
280 x 1
024 91.1 85.0 157.5 B
– – –
D/R
SXGA+
1
400 x 1
050 65.2 60.0 122.6 A
3 – 3
D/R
1
400 x 1
050 82.2 75.0 155.9 B
– – –
D/R
WXGA+ 1
440 x 900 55.9 59.9 106.5 A
– – –
D/R
UXGA 1
600 x 1
200 75.0 60.0 162.0 B
3 – 3
D/R
WSXGA+ 1
680 x 1
050 65.3 60.0 146.3 A
– – –
D/R
1920 x 1080
*2
1
920 x 1
080 66.6 59.9 138.5 A
– – –
D/R
WUXGA
*2
1
920 x 1
200 74.0 60.0 154.0 B
3 – 3
D/R
*1: When the 1035/60i signal is input, the signal is displayed as 1080/60i.
*2: VESA CVT-RB (Reduced Blanking) compatible
*3: Signals that show display picture quality are as follows.
AA : Projects the image in the highest picture quality.
A : Converts the image in the image processing circuit and projects the image.
B : Samples the image in the image processing circuit and projects the image.
*4: Signal A for PT-DX800E.
*5: Signal A for PT-DW730E.
*6: Signals with a 3 in Plug and play are signals described in the projector's EDID (extended display identication data). If a signal
has no 3 in Plug and play but has an entry in the Format column, it can be entered. For signals without a 3 in Plug and play,
there are instances that resolution cannot b
e selected even though the computer supports them.
*
7: Signals that show formats are as follows.
V: Video
S: S-Video
D: DVI-D
R: RGB
Y: YP
B
P
R
Note
z
The number of display dots is 1 280 x 800 for the PT-DW730E and 1 024 x 768 for the PT-DX800E. A signal
with a different resolution will be projected after converting the resolution to match the projector display.
z
The
“
i
”
at the end of the resolution indicates an interlaced signal.
z
W
hen interlaced signals are connected, icker may occur on the projected image.
To Next Page
Loading...
