To Next PageTo Next PageWhy image output from DVI-D of the computer does not appear on Panasonic PT-DZ870U?
If the image output from the DVI-D connection of your computer isn't appearing on the Panasonic Projector, check if the [DVI-D IN] setting is set to [EDID3] or [EDID2:PC]. Consider updating the graphics accelerator driver of your computer to the latest version. It may also be necessary to restart the computer after performing the [DVI-D IN] setting.
Why is my Panasonic Projector remote control not responding?
If your Panasonic Projector remote isn't working, check these potential causes: Ensure the batteries aren't depleted and are inserted with the correct polarity. Make sure there are no obstructions between the remote and the projector's signal receiver. Verify the remote is within its effective range. Also, check if other light sources are interfering with the signal. Confirm that the [REMOTE CONTROL] setting in [CONTROL DEVICE SETUP] isn't set to [DISABLE], and that the terminal isn't being used for contact control. Finally, ensure the ID number setting operation is correct.
What to do if no image appears on Panasonic Projector?
If no image appears on your Panasonic Projector, consider the following: Check that connections to external devices are correctly performed and the input selection setting is correct. Ensure the [BRIGHTNESS] adjustment isn't at a minimum. Verify the external device connected to the projector is working correctly and that the shutter function isn't in use. Finally, make sure the lens cover is removed.
How to fix a fuzzy image on Panasonic Projector?
To resolve a fuzzy image on your Panasonic Projector, try the following: Ensure the lens focus is set correctly and the projection distance is appropriate. Check if the lens is dirty and clean it if necessary. Also, verify that the projector is installed perpendicular to the screen.
How to display image from a computer on Panasonic PT-DZ870U?
If the image from your computer isn't appearing on the Panasonic Projector, consider these points: Use a D-Sub cable that is 10 m (32'10") or shorter. Check the external video output settings on your laptop. These settings may be switched by pressing “Fn” + “F3” or “Fn” + “F10” simultaneously, but the method varies depending on the computer type, so refer to your computer's user manual.
Why image does not display correctly on Panasonic PT-DZ870U Projector?
If the image isn't displaying correctly on your Panasonic Projector, ensure the [SYSTEM SELECTOR] selection is set correctly. Check for any problems with the video tape or other image sources. Verify that the input signal is compatible with the projector.
Why does the image in the 3D eyewear flicker when using Panasonic PT-DZ870U?
If the image in the 3D eyewear flickers when using your Panasonic Projector, make sure you are within the reception range.
How to control Panasonic Projector with Art-Net?
To control your Panasonic Projector with Art-Net, ensure the connections between the twisted-pair-cable transmitter and the projector or an external device are correctly done. Verify that the [Art-Net] setting is [ON]. Also, confirm that the [PORT ADDRESS] and [START ADDRESS] settings are correct.
How do I display the menu screen on my Panasonic PT-DZ870U?
If the menu screen isn't appearing on your Panasonic Projector, check if the on-screen display function is turned off (hidden).
What to do if the 3D function is not working on Panasonic Projector?
If the 3D function isn't working on your Panasonic Projector, check the following: Ensure the [3D INPUT FORMAT] setting in [3D SETTINGS] is correct. Verify the 3D eyewear settings are correct. Confirm that the input signal is supported by the projector.
General| Brightness | 8500 lumens |
|---|---|
| Light Source | Lamp |
| Max Resolution | 1920 x 1200 (WUXGA) |
| Projection Size | 40 - 600 inches |
| Resolution | 1920 x 1200 |
| Connectivity | HDMI, DVI-D, RS-232C, LAN |
| Lamp Type | UHM Lamp |
| Power Consumption | 450W (Normal mode), 380W (Eco mode) |
