Panasonic SB-TP1000 User Manual

RQT8808
6
•Do not apply an unreasonable force to the net at the front of the
speaker unit. You cannot remove the front net.
•You can carry out assembly work stably by placing the cushions in
the packing case beneath the speaker. Place the net sides of the
speaker units face up.
Cushions used
Speaker units.
Use the four cushions at the very top of the SB-FS1000.
Method of setting cushions
Place these surfaces face up.
Be sure to spread a cloth, for example, on the floor to protect it from
damage.
•After each task, tighten the screws securely.
1.Fit the stand bases onto the front speaker stands.
Align the two projections in one of the front speaker stands
(provided) with the two holes in the front R stand base
(provided), and fit together.
•The packing bag for the front R stand base and the packing bag
for the front center speaker R are held in place by tape of the
same color. Assemble the base and speaker with the same color
tape.
•Similarly, the packing bag for the front L stand base and the pack-
ing bag for the front center speaker L are held in place by tape of
the same color.
Attach the stand base using the two stand base mounting
screws (provided).
Use the two screw holes marked “R” to attach the base.
•Align the positions of the holes marked “R” with the positions of
the screw holes in the stand. If the positions do not line up,
change the direction of the stand. (The base can be fitted onto
the top or bottom of the stand.)
•When assembling front speaker L, use the screw holes marked
“L” and fit.
•Tighten the screws alternately, and finally tighten them hard.
Reverse side of stand base
2.Fit the stand onto front speaker R.
Align the two projections in the assembled stand with the two
holes in front speaker R , and fit together.
Attach the stand using the stand mounting screw (pro-
vided).
Use the center screw hole to fit the stand on to the speaker.
3.Connect the speaker cables (not provided) to the
terminals.
Before connection, pass the speaker cords through the hole marked
“R” in the back of the stand base.
(Use the hole marked “L” for the left front speaker.)
Speaker cables (approx. 4 m)
(–) cable :
Connect this to the “CENTER” black negative (–) terminal.
(+) cable :
Connect this to the “CENTER” red positive (+) terminal.
Speaker cables (approx. 4 m)
(–) cable :
Connect this to the “LF” black negative (–) terminal.
(+) cable :
Connect this to the “HF” red positive (+) terminal.
Do not remove the shorting bars.
Turn the thumb nut in the loosening direction until the hole
in the terminal becomes visible.
Insert the conductor into the hole, and tighten the thumb
nut.
When using banana plugs (4 mm plugs)
Loosen the screws of the banana plugs (provided).
Twist the conductors of the speaker cable.
Insert the speaker cables all the way, then firmly tighten
the screws.
Tighten the thumb nuts of the terminals all the way, and connect
the plugs.
•When using commercially available banana plugs, use banana
plugs that have an overall diameter of 10 mm or less.
Do not use the banana plugs when the speakers are to be mounted
on a wall.
Never short-circuit positive (+) and negative (–) speaker wires.
4.Fix the speaker cables.
Press the speaker cables into the cable groove provided in the stand.
The speaker cables must have a thickness of 2.8 mm or less to fit into
the cable groove.
Cable groove
When using speaker cables that are thicker than 2.8 mm, attach
nylon clampers to the speakers and use them to fix the cables.
Example Nylon clamp (provided)
Screw for nylon clamp (provided)
Speaker cables
Repeat steps 1 to 4 and assemble front speaker L.
R
R
Assembly and Installation
Assembling the front speakers as stand types

Panasonic SB-TP1000 Specifications