To Next PageTo Next PageHow to troubleshoot a Panasonic SC-AK100 Stereo System remote control that is not working?
If your Panasonic Stereo System's remote control isn't working, first, check that the batteries are correctly inserted. If they are, try replacing them with new ones.
Why does my Panasonic SC-AK100 have no sound, or the sound stops?
Several factors can cause sound issues. First, check the speaker connections. If the positive and negative speaker wires are shorting, or the speakers are strained due to high volume or power, or if the unit is in a hot environment, switch off the unit, identify and fix the cause, then switch it back on. Also, keep AC power cords and fluorescent lights away from the unit's cables. If “F61” is displayed and the problem persists, there may be a power supply issue; in that case, consult the dealer. If “– –:– –” appears on the display at standby mode, you plugged in the AC power supply cord for the first time or there was a power failure recently, set the time. If “ERROR” is displayed, an incorrect operation was performed, read the instructions and try again.
What to do if the TV picture disappears when using my Panasonic SC-AK100 Stereo System?
If the picture on your TV disappears or stripes appear when using your Panasonic Stereo System, it might be due to the antenna's location or orientation. If you're using an indoor antenna, switch to an outdoor one. Also, ensure the TV antenna wire is not too close to the unit; separate them if necessary.
Amplifier Section| power output (60 Hz–16 kHz, both channels driven) | 40 W per channel (6 Ω) |
|---|---|
| power output (1 kHz, both channels driven) | 50 W per channel (6 Ω) |
| input sensitivity (AUX) | 250 mV |
| input impedance (AUX) | 13.3 kΩ |
FM Tuner Section| frequency range (200 kHz steps) | 87.9 – 107.9 MHz |
|---|---|
| frequency range (100 kHz steps) | 87.5 – 108.0 MHz |
| sensitivity | 2.5 µV (IHF) |
| S/N 26 dB | 2.2 µV |
| antenna terminal | 75 Ω (unbalanced) |
AM Tuner Section| frequency range | 520 – 1710 kHz (10 kHz steps) |
|---|---|
| sensitivity (S/N 20 dB at 1000 kHz) | 560 µV/m |
Cassette Deck Section| track system | 4 track, 2 channel |
|---|---|
| record/playback head | Solid permalloy head |
| erasure head | Double gap ferrite head |
| motor | DC servo motor |
| recording system | AC bias 100 kHz |
| erasing system | AC erase 100 kHz |
| tape speed | 4.8 cm/s (1[7]/8 ips) |
| overall frequency response (NORMAL TYPE I) | 35 Hz – 14 kHz |
| S/N | 50 dB (A weighted) |
| wow and flutter | 0.18% (WRMS) |
| fast forward and rewind time | Approx. 120 seconds with C-60 cassette tape |
CD Section| sampling frequency | 44.1 kHz |
|---|---|
| decoding | 16 bit linear |
| beam source/wavelength | Semiconductor laser/780 nm |
| number of channels | Stereo |
| frequency response | 20 Hz–20 kHz (+1, –2 dB) |
| wow and flutter | Below measurable limit |
| digital filter | 8 fs |
| D/A converter | MASH (1 bit DAC) |
Speaker Section| type | 2 way speaker system |
|---|---|
| woofer | 10 cm (4˝) cone type |
| super tweeter | Piezo type |
| impedance | 6 Ω |
| input power | 80 W (Music) |
| output sound pressure level | 86 dB/W (1.0 m) |
| cross over frequency | 10 kHz |
| frequency range | 54 Hz–19 kHz (–16 dB), 75 Hz–17 kHz (–10 dB) |
| dimensions (WxHxD) | 190 x 315 x 190 mm (7[15]/32˝ x 12[13]/32˝ x 7[15]/32˝) |
| mass | 2.4 kg (5.3 lb.) |
General| power supply | AC 120 V, 60 Hz |
|---|---|
| power consumption | 120 W |
| standby power consumption | Approx. 0.49 W |
| dimensions (WxHxD) | 250 x 315 x 345 mm (9[27]/32˝ x 12[13]/32˝ x 13[19]/32˝) |
| mass | 6.4 kg (14.1 lb.) |
Essential safety warnings and cautions for operating the unit safely.
Information regarding compliance with FCC rules for digital devices.
Covers power source, polarization, cord protection, overloading, and attachments.
Guidance on unit placement for ventilation, avoiding foreign material, and magnetism.
Recommendations for unit placement regarding water, moisture, and heat.
Instructions for cleaning and when to seek qualified service personnel.
Lists all items included in the product package for identification.
Details on battery installation, usage range, and sensor aiming.
Instructions for connecting FM indoor and AM loop antennas.
Guidance on connecting speakers and the AC power supply cord.
Identification and function of controls on the main stereo unit.
Explanation of buttons and their functions on the remote control.
Step-by-step instructions for manually tuning radio stations.
Methods for automatically or manually presetting radio stations.
Guidelines for choosing and handling CDs to prevent damage.
How to play, pause, stop, search, and skip tracks on CDs.
Understanding the CD display for track and time information.
How to play specific tracks or program a sequence of tracks.
Using different play modes like ALL-DISC, 1-SONG, RANDOM, and repeat.
Reducing noise during AM recording and preventing tape erasure.
Connecting antennas and external audio sources for playback/recording.
Guidelines for using headphones and avoiding prolonged listening.
Controlling the demo display and enabling power-saving auto-off.
Adjusting display brightness and temporarily muting audio.
Instructions for setting the 12-hour clock for timers and display.
Setting timers for automatic playback or recording.
Setting a timer to automatically turn off the unit.
Instructions for cleaning the exterior of the unit.
Guidance on cleaning the cassette deck heads for optimal performance.
Details on when service is required and replacement parts.
Contact information and locations for product assistance and service.
