What to do if Panasonic SC-AK29 Stereo System remote control not working?
If the remote control is not operating your Panasonic Stereo System, check if the batteries are installed with the correct polarity. If not, re-insert the batteries in the correct polarity.
How to improve distorted sound during stereo broadcast on Panasonic SC-AK29?
If the sound during a stereo broadcast is highly distorted on your Panasonic Stereo System, there may be a building or mountain nearby. Use a high-grade outdoor antenna and install it in a good location, height, and orientation for reception.
What to do if Panasonic SC-AK29 disc play does not start or shows incorrect indication?
If the display on your Panasonic Stereo System does not show the correct indication, or disc play does not start when you press the play button, the disc may be upside down. Set the disc with the label facing upward.
Why are left and right sounds reversed when listening to external unit on Panasonic SC-AK29?
If the left and right sounds are reversed when listening to an external unit on your Panasonic Stereo System, the left and right connections to the external unit are reversed. Connect the external unit’s cord correctly.
What to do if Panasonic Stereo System displays 'TAKE OUT/DISC'?
If “TAKE OUT/DISC” appears on the display of your Panasonic Stereo System, there was a power failure or the power cord was disconnected during disc changing or when the disc tray was open. To resolve this: 1. Press [f/7, POWER] to switch on the power. The tray will open. 2. If there is a CD in the tray, remove it, then press [c] of [CD 1] to close the tray. The system will restore normal operation.
What to do if my Panasonic Stereo System deck does not enter recording mode?
If the deck on your Panasonic Stereo System does not enter recording mode, it could be because the erase-prevention tabs have been removed from the cassette. Attach tape to cover the space left by the removal of the erase-prevention tabs.
Why does Panasonic SC-AK29 display 'ERROR' message?
If the “ERROR” message appears on the display of your Panasonic Stereo System, it indicates that an incorrect operation has been performed. Operate the unit correctly by following the operating instructions.
What to do if Panasonic SC-AK29 Stereo System displays “– – : – –”?
If “– – : – –” appears on the display of your Panasonic Stereo System, it could be because you plugged in the power cord for the first time or there was a recent power failure. You should set the time.
How to fix reversed left and right sounds on Panasonic SC-AK29?
If the left and right sounds are reversed on your Panasonic Stereo System, the left and right connections to the speaker are likely reversed. Connect the speaker cords correctly.
How to fix no sound on Panasonic SC-AK29?
If there is no sound when playing a source on your Panasonic Stereo System, the (+) and (–) wires of the speaker cords may be shorted. Switch the system to standby mode, reconnect the speaker cords so they are not shorted, and then switch the power back on.
Amplifier Specifications| RMS power output (60 Hz–120 Hz, both channels driven) | 70 W per channel (6 Ω) |
|---|---|
| RMS power output (120 Hz–14 kHz, both channels driven) | 30 W per channel (6 Ω) |
| Total Bi-Amp power | 100 W per channel |
General Specifications| Power supply | AC 120 V, 60 Hz |
|---|---|
| Power consumption | 165 W |
| Dimensions (WxHxD) | 270 x 330 x 335 mm |
Speaker Specifications| Type | 4 way speaker system |
|---|---|
| Super Woofer | 17 cm (6[11]/16˝) cone type |
| Weight | 5.1 kg (11.2 lb.) |
Amplifier Specifications| RMS power output (60 Hz–120 Hz, both channels driven) | 55 W per channel (6 Ω) |
|---|---|
| RMS power output (120 Hz–14 kHz, both channels driven) | 20 W per channel (6 Ω) |
| Total Bi-Amp power | 75 W per channel |
General Specifications| Power supply | AC 120 V, 60 Hz |
|---|---|
| Power consumption | 130 W |
| Dimensions (WxHxD) | 270 x 330 x 335 mm |
Speaker Specifications| Type | 3 way speaker system |
|---|---|
| Super Woofer | 14 cm (5[1]/2˝) cone type |
| Weight | 4.5 kg (9.9 lb.) |
Amplifier Specifications| RMS power output (1 kHz, both channels driven) | 50 W per channel (6 Ω) |
|---|---|
| RMS power output (70 Hz–16 kHz, both channels driven) | 46 W per channel (6 Ω) |
| Input sensitivity AUX | 250 mV |
General Specifications| Power supply | AC 120 V, 60 Hz |
|---|---|
| Power consumption | 145 W |
| Dimensions (WxHxD) | 270 x 330 x 310 mm |
Speaker Specifications| Type | 2 way speaker system |
|---|---|
| Woofer | 12 cm (4[23]/32˝) cone type |
| Weight | 3.0 kg (6.6 lb.) |
Guidelines for power source, polarization, cord protection, and nonuse periods.
Instructions for inserting and handling batteries in the remote control.
Details on proper orientation and distance for remote control operation.
Instructions for connecting FM antenna, AM antenna, and speakers.
Details of controls located on the main unit A with reference pages.
Details of controls located on the center console B with reference pages.
List of remote control buttons and their corresponding functions and page references.
Guide to automatically or manually presetting radio stations for easy tuning.
Method for automatically tuning into radio stations.
How to stop playback of a CD.
How to start CD playback automatically from standby mode.
Instructions for pausing, searching, and skipping tracks during playback.
How to select and play a specific track directly.
How to set the unit to repeat playback of all tracks or specific tracks.
How to play tracks in a random order.
How to program a sequence of tracks for playback.
Information on tape types that can be played correctly.
How to play, fast-forward, rewind, and adjust volume for tapes.
Solutions for common issues affecting the entire system.
Guidance for resolving noise and reception issues during FM listening.
Solutions for beat sounds and hums during AM listening.
How to resolve picture disruption when a TV is nearby.
Solutions for common problems with tape decks and CD players.
Troubleshooting remote control issues and basic maintenance tips.
To Next Page