To Next PageTo Next PageHow to fix a Panasonic Stereo System remote control that isn't working?
If your Panasonic Stereo System remote control isn’t working, first ensure the batteries are correctly inserted. If the problem persists, replace the batteries, as they may be worn.
What to do if my Panasonic Stereo System shows 'No play'?
If your Panasonic Stereo System isn't playing discs, it could be due to several reasons: * The disc might not be correctly set. * The disc could be scratched or dirty. * There might be moisture on the lens; wait about an hour and try again.
How to stop humming during play on my Panasonic SC-EN27?
If you are hearing a humming sound during play on your Panasonic Stereo System, it could be due to an AC mains lead or fluorescent light being near the cords. To fix this, keep other appliances and cords away from the unit’s cords.
How to reduce hum during AM broadcasts on Panasonic SC-EN27?
If your Panasonic Stereo System is producing a low hum or noise during AM broadcasts, keep the antenna away from other cables and cords and away from the unit itself.
What does 'ERROR' mean on my Panasonic SC-EN27?
The 'ERROR' message on your Panasonic Stereo System indicates that an incorrect operation was performed. Read the instructions and try again.
What to do if the Panasonic SC-EN27 Stereo System remote control doesn’t work?
If the remote control for your Panasonic Stereo System isn't working, try replacing the batteries first.
Why is there no sound or a lot of noise coming from my Panasonic SC-EN27 Stereo System?
If you are experiencing no sound or excessive noise with your Panasonic Stereo System, try the following: * Ensure the unit is away from mobile telephones. * Increase the volume. * Turn the unit off and then back on again.
How to fix 'MP3 cannot be read' error on Panasonic SC-EN27 Stereo System?
If your Panasonic Stereo System cannot read MP3 files, it might be because you copied a multi-session disc without closing the session. It is necessary to close the session. Also, the amount of data on the disc may be too small, so set the amount of data to greater than approximately 5 MB.
Why does my Panasonic Stereo System display – –:– –?
If your Panasonic Stereo System displays '– –:– –', it likely means the unit was recently plugged in or there was a power failure. To resolve this, set the time. Also, note that the total programmed play time cannot exceed 200 minutes, though tracks can still be programmed and played.
How to eliminate beat sound during radio broadcast on Panasonic SC-EN27 Stereo System?
If you are receiving a radio broadcast on your Panasonic Stereo System and hear a beat sound or noise, try switching off the TV or any other audio players, or separate them from the unit. If a portable audio player is connected to the 'MUSIC PORT', switch it off.
Radio| FM frequency range | 87.50 MHz to 108.00 MHz |
|---|---|
| AM frequency range (9 kHz steps) | 522 kHz to 1629 kHz |
| AM frequency range (10 kHz steps) | 520 kHz to 1630 kHz |
CD Player| sampling frequency | 44.1 kHz |
|---|---|
| decoding | 16 bit linear |
| beam source wavelength | 795 nm |
Terminals| input terminal | MUSIC PORT: Ø 3.5 mm stereo (33 kΩ) |
|---|---|
| output terminal | PHONES: Ø 3.5 mm stereo (32 Ω) |
| D/A converter | MASH(1 bit DAC) |
General| power supply (Europe and UK) | AC 230 V to 240 V, 50 Hz |
|---|---|
| power supply (other areas) | AC 220 V to 240 V, 50/60 Hz |
| power consumption | 15 W |
Speakers| full range | 8 cm, 6 Ω×2 |
|---|---|
| speaker dimensions | 91 mm×206 mm×176 mm |
| power consumption in standby mode | 1.6 W |
Weight and Dimensions| main unit dimensions | 241 mm×206 mm×206 mm |
|---|---|
| mass with speakers | 3.1 kg |
| mass without speakers | 1.8 kg |
Loading a CD into the unit and preparing for playback.
Initiating CD playback and one-touch play functionality.
Navigating between tracks or searching within a track.
Setting playback modes like one-track repeat, all-track repeat, or random play.
Creating a custom playback sequence of up to 24 tracks.
Presetting available radio stations into memory channels.
Setting the unit to turn off automatically after a set time.
Setting the unit to start playing a selected source at a specific time.
Restrictions and compatibility issues related to MP3 playback.
Warnings about using appropriate voltage sources.
Safety instructions for handling the power cord.
Precautions against foreign objects and liquids entering the unit.
Instructions regarding self-repair and contacting service personnel.
Technical specifications for the main audio system unit.
