Panasonic SC-HTX5

RQT9478
21
Setting distances
You can make this setting when connecting the wireless
surround speakers with SH-FX70. (➜ page 14) This setting is
not displayed in other conditions.
By setting the distance from front/surround speakers to the
listening-viewing position, the sound delay time is automatically
calculated and adjusted so that sound reaches the listener at
the same time.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ left)
2. Press [
w
][
q
] to select “DISTANCE ” and
press [OK].
3. Press [
w
][
q
] to select a speaker to set
and press [OK].
FRONT : Front speakers
SURR : Surround speakers
4. Press [
e
][
r
] to select the distance and
press [OK].
Adjustment range: 1.0 to 10.0 m
Factory setting: Front 3.0 m
Surround 1.5 m
5. Press [ RETURN] several times to select
“EXIT ” and press [OK] to fi nish the
setting.
Reducing standby power
consumption (HDMI off mode)
Standby through function (➜ pages 11 and 25) does not work in
this mode if you have connected through the HDMI terminal.
VIERA Link “HDAVI Control” (➜ page 18) will not function when
this system is off.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ left)
2. Press [
w
][
q
] to select “HDMI ” and press
[OK].
3. Press [
w
][
q
] to select “STNBY ” and
press [OK].
4. Press [
e
][
r
] to select “OFF ” and press
[OK].
OFF : Standby power consumption reduced
(approx. 0.1 W)
ON : “Standby through” is activated when this system is
turned off. (Normal power consumption)
Factory setting: ON
5. Press [ RETURN] several times to select
“EXIT ” and press [OK] to fi nish the
setting.
 Setup menu items
•
✽
appears only when audio adjustment can be made.
• Select “EXIT ” and press [OK] to fi nish the setup mode.
Adjusting sound quality
You can adjust the level of bass and treble.
This setting is effective only when you perform stereo playback
of 2-channel analogue and PCM signals.
This setting is not displayed in other conditions. Be sure to
make this setting in the above condition.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ above)
2. Press [
w
][
q
] to select “BASS ” or
“TREBLE ” and press [OK].
3. Press [
e
][
r
] for adjustment, and press
[OK].
Adjustment range: –6 to +6
Factory setting: 0
4. Press [ RETURN] several times to select
“EXIT ” and press [OK] to fi nish the
setting.
Adjusting the volume balance of
front speakers
You can adjust the balance of the front speakers.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ above)
2. Press [
w
][
q
] to select “BALANCE ” and
press [OK].
3. Press [
w
][
q
] for adjustment, and press
[OK].
L : Front left
R : Front right
Move the bar to left and right on the display to adjust.
• As the bar gets closer to “L ”, the sound moves to left
front.
• As the bar gets closer to “R ”, the sound moves to
right front.
4. Press [ RETURN] several times to select
“EXIT ” and press [OK] to fi nish the
setting.
The bar indication is approximate.
Functions and settings
Play
✽
“BASS”
✽
“TREBLE”
“BALANCE”
✽
“DISTANCE” “HDMI”
✽
“STB AUDIO”
“ SOUND DLY ” “DUAL PRG” “ DRCOMP ”
“ ATTENUATOR ” “REMOTE”
“EXIT”
“ INPUT MODE”
“RESET”
Note