Panasonic SUNX CX-400 Series - Specifications

5
11 SPECIFICATIONS
Item
Thru-beam
Retroreflective type with
polarizing filter
*1
*1
The retroreflective type sensor with polarizing filters may not stably detect specular or glossy objects through transparent film since light is polarized by the
transparent film. For details, see page 4, section 8, RETROREFLECTIVE TYPE SENSOR WITH POLARIZING FILTERS.
Diffuse reflective
Narrow view
reflective
Short sensing
range
Long sensing
range
CX-411 (NPN)
*2
*2
Model nos. with the suffix -J indicate the M12 pigtailed type. The suffix -Z indicates the M8 connector type.
CX-491 (NPN)
*2
CX-421 (NPN)
*2
CX-422 (NPN)
*2
CX-423 (NPN)
*2
CX-411-P (PNP)
*2
CX-491-P (PNP)
*2
CX-421-P (PNP)
*2
CX-422-P (PNP)
*2
CX-423-P (PNP)
*2
Sensing range
10m
3m
*3
*3
The sensing range and the sensing object for the retroreflective type sensor is specified for the RF-230 reflector.
300mm
*4
800mm
*4
70 to 200mm
*4
Object to be sensed
∅ 12mm or more opaque
object
∅ 50mm or more opaque,
translucent or specular
object
*3
Opaque, translucent or specular Opaque, translucent
or transparent object
(Min. ∅ 0.5mm
copper wire)
Repeatability
(perpendicular to sensing axis)
0.5mm or less 1mm or less 0.5mm or less
Supply voltage
12 to 24V DC ±10% Ripple P-P 10% or less
Current consumption
Emitter: 20mA or less
Receiver: 20mA or less
20mA or less 25mA or less 20mA or less
Output
NPN output type
• NPN open-collector transistor
• Maximum sink current: 100mA
• Applied voltage: 30V DC or less (between output and
0V)
• Residual voltage: 1V or less (at 100mA sink current),
0.4V or less (at 16mA sink current)
PNP output type
• PNP open-collector transistor
• Maximum source current: 100mA
• Applied voltage: 30V DC or less (between output and +V)
• Residual voltage: 1V or less (at 100mA source current), 0.4V or
less (at 16mA source current)
Output
operation
Light-ON or Dark-ON
Short-
circuit
protection
Incorporated
Response time 1ms or less
Operation indicator Orange LED, lights up when the output is ON. Thru-beam type sensor: located on the receiver.
Stability indicator
Green LED, lights up under stable light received condition or stable dark condition. Thru-beam type sensor: located on the
receiver
Power indicator
Green LED, lights up
when the power is ON.
Located on the emitter
_____________________
Sensitivity adjuster Available.
Automatic
interference
prevention function
_____
*5
Incorporated, two sets of sensors can be mounted close together.
Protection IP67 (IEC)
Ambient temperature -25 to +55°C (No dew condensation or icing allowed), Storage: -30 to +70°C
Ambient humidity 35 to 85% RH, Storage: 35 to 85% RH
Emitting element
Red LED (modulated) Infrared LED (modulated) Red LED
(modulated)
Material Enclosure: PBT, Lens: Acrylic, Indicator cover: Acrylic
Cable
0.2mm
2
3-core (thru-beam type sensor emitter: 2-core) cabtyre cable, 2m long
Weight
Emitter: 45g approx.
Receiver: 50g approx.
50g approx.
Accessory _____ RF-230 (Reflector): 1 pc. _____