Panasonic Technics SL-1800

4, Turn the entire balance weight clockwise (indicated by the
arrow
A")
of
countrerclockwise
(indicated
by
the
arrow
“B")
until the tonearm is approximately balanced horizontally.
(See Fig. 10).
Balance weight
Gueing lever
Tubular arm
re
a ~ =
5.
Altor
the
tonearm
is
horizontally
balanced,
temporarily
fix
the
tonearm
by the arm clamp.
(Refer
to Fig. 11)
Hola
the balance
weight
stationary
with fingers
as shown
in
Fig. 11 and rotate
only the stylus
pressure
ring to bring
the
‘numeral
"0" of the ring into alignment
with the centre
line
‘on the tonearm rear shatt, (The adjustment of the horizontal
balance
is
now
completed.)
Note:
1) During the adjustment of the horizontal balance, be sure
that the stylus tip of the cartridge does not contact the
turntable mat or turntable base.
Ensure that the anti-skating knob is at "0" position. (See
Fig. 11)
‘There are cases where the tonearm may sway or flow
Slightly at the position of "0" due to the highly sensitive
rotational part of the tonearm, but this side force is trivial
‘and presents no inconvenience.
Peoressure ring “0
3) Ensure that ine cueing lever is in the lowered position as
shown in Fig. 10.
4) Make certain that the speed selector is in the "s position.
the
balance
adjustment
is
easily
made
as
the
turntable
platter
remains
stationary,
Atter
adjusting
the
horizontal
balance,
turn
the
balance
weight
clockwise in the direction of the arrow and align the correct
stylus
pressure.
(Follow
the
cartridge
manufacturer's
recommendation.)
(See
Fig.
12)
:
Note
1) As the stylus pressure ring rotates together with the ba-
lance
weight.
proper
stylus
pressure
can
be
selected
by
directly
reading
the
graduated
ring,
2) Set the stylus pressure to the maximum value of your
Cartridge in cases where the record has an extremely high
recording level, or where the unit is operated in @ room at
low
temperature
or
in
places
in
which
the
unit
is
liable
to be subjected to vibrations
@anti-s
skating force control.
Set the anti-skating force control to the same value as that set
tor
stylus
pressure.
(See
Fig.
13)
Place the dust cover into position from directly above
at both sides. For detaching the dust cover, be c
raise it as illustrated betore removal
holding it
tain first to
Dust ccver
Note
Opening or closing of the dust cover during playing should be
made as gently as possible, since this may not only cause
harmful
vibrations,
but
also
result
in
skipping
of
the
stylus.
@Placement.
1.
Use
the
unit
in
a
stable
and
horizontal
position,
where
there
is little or no vibration,
2.
Use
the
unit
as
far
away
from
the
speakers
as
possible
and
isolate
the unit from
sound
radiation
from
them.
3. Do net place the unit where it is exoosed to direct sun, dust,
moisture or heat
4. Keep it in a well-ventilated place.
@connect the AC power plug.
Connect the AC power plug to the AC socket
Jn cases where the AC power plug is connected to the outlet
(AC outlet) of the amplifier. receiver and the like. make sure
that the wattage indicated on the outlet corresponds to the
turntable's requirements botore connecting the power plug
‘®Cconnect the output terminal
‘Output termi or Receiver
Lwnite) Channel
R (Red) Channel
E (Spade !ug) ——- EX)
Note:
Be sure to connect the ground terminal to the amplifier of
receiver. It this connection is not made or is loose, a power
source HUM” will result