40
Options Adjustments
Item Adjustments
Input lock
Locks the input switch operation.
Off
PC DVI HDMI1 HDMI2 Off
Notes:
• Only the adjusted signal is displayed (see page 17).
• Input switch can be used when this is set to “Off”.
Button lock
Off
On MENU&ENTER
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
and buttons on main unit.
On: Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
Off: Press
four times→Press four times→Press four times→Press
MENU&ENTER: Press four times→Press four times→Press four times→Press
On: Press four times→Press four times→Press four times→Press
Remocon User level
Off
User1 User2 User3
Off: You can use all of the buttons on the remote control.
User1: You can only use
, , , , buttons on the remote control.
User2: You can only use
button on the remote control.
User3:
Locks all the buttons on remote control.
Off-timer function
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Note: When “Disable” is set, the Off-timer is cancelled.
Initial Power Mode
Normal
On Standby
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby
: Power returns in standby mode. (Power Indicator : red/orange)
On: Power returns in power On. (Power Indicator : green)
Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
Power ON Screen
Delay
Off
1 2 3.... 30
You can set the power-on delay time of the displays to reduce the power load, when you press
to
turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display’s setting individually.
Off: The display will be turned on at the same time as
is pressed.
1 to 30 (sec.)
: Set the power-on delay time (second).
After pressing , the display will be powered on with time delay depending on this setting.
Notes:
• During this function is working, the power indicator is blinking green.
•
This function also works when the power recovers from failure or after plugging off and in again the power cord.
Clock Display
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
button is pressed.
Note: When “PRESENT TIME Setup” is not set, the clock is not displayed even
if “Clock Display” is “On”. (see page 28)
Power On Message
(No activity power
off)
Whether to show/hide No activity power off Precautions at the time of power ON is set.
On: The warning precautions are shown at the time of power ON.
Off: The warning precautions are not shown at the time of power ON.
Note: This setting is enabled only if “No activity power off” is “Enable” (see page 32).
Winter Mode
Set this function to maintain the image quality when the product is used in a low temperature
environment of 39 °F/4 °C or lower.
Off: Normal standby operation
On:
Image is muted at standby and backlight is turned on when the inside temperature of the display is 32 °F/0 °C or lower
to prevent decreasing the temperature. Backlight is turned off when the inside temperature is 50 °F/10 °C or higher.
When this function is set to “On”, the following message appears at standby.
Notes:
• Do not unplug the power cable while using the product with this function “On”.
• When this function is set to “On”, the power consumption at standby is approx. 110 W.
• Turn this function “Off” to use this product in an environment of 39 °F/4 °C or higher.
• The fans spin while this is set to “On” even if the Display is in standby mode.
Power Switch Lock
Sets the lock setting for the display Power switch.
On: Power switch operation is disabled.
Off: Power switch operation is enabled.
Winter mode is active.
10:00
To Next Page
Loading...
