Only bypass code reported on bypass arming
Zone doubling (ATZ)
[7]
[8]
(default = " ")
ZONE DEFINITION:
Instant = ON
Follow = ON
If , zone is ARMED
on stay or split arming
ON
Bypass enabled = ON
Silent =ON
Fast =ON
226224
230
228
242
** Zone Swap
240 SYSTEM A SYSTEM B
238236
218216
214212
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
[2]
[1] [6]
[11]
[8]
[10]
[7]
[9]
[12]
[5]
[4]
[3]
KEY SELECT:
[1]
[2]
[6]
[11]
[8]
[10]
[7]
[9]
[12]
[5]
[4]
[3]
Delay 2 =ON
234232
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
24 Hr./ Fire =ON
*When zone 3 is defined "24 Hour" it becomes a fire zone
222
220
5
24
1
3
6
11
8
10
7
9
12
5
24
1
3
6
11
8
10
7
9
12
NOTE: 220 234Zones not selected at addresses to are "Delay 1" zones.
- 7 -
210:
Exclude AC from trouble display
[2 ]
ND
OFF / ON
[3]
[1]
disabled (in case of fire zone 3 only)
enabled
auto away
Arming regular
[2]
stay armAuto arm = regular arm / (A + B)
KEY
[6]
tamper follows zone bypass definitionNo tamper bypass
[5]
[4]
[9]
enabled
enabled
disabled
Audible trouble warning
enabled
*Only installer can clear tamper trouble.
enabled
Arm-inhibit on tamper*
Arm-inhibit on batt fail
Note: Default = " " for addresses to
OFF
1) Press + installer code (default 747474). key will flash.
2) Enter 3 digit memory address ( to ).
3) Press corresponding key to select option.
4) To change selection press key again.
5) To save press .
6) Repeat steps 3 to 5 for addresses to
7) To exit programming mode press
Feature selection programming addresses to The " "/" " status of the lights (keys) determines features selected.
ON OFF
FEATURE SELECT (LIGHT ON/OFF) PROGRAMMING
PG728
Zone 6
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
Zones 13 to 24 are not available.
N/A
**See installation manual "Partitioning"
[1]
[2]
[3]
[4]
[5]
[6]
1 7
2 8
3 9
4 10
5 11
6 12
Zone Swap
Recommended for use with partitioned systems only.
To Next Page
Loading...
Need help?
General
