c) Allow only responsible adults who have read and understood the manual to operate this machine.
d) Be familiar with all controls and proper operation. Know how to stop the machine quickly in the event of an
emergency.
e) Don’t operate the machine while under the influence of alcohol, drugs or medication.
f) Only a single operator is allowed to load and operate this log splitter. Keep bystanders, helpers, pets and
children a sufficient distance to the machine.
g) Only use your hands to operate the control handle and switch. Arms, feet, knees, rope, heavy objects and
extension device are not allowed.
h) Never put any part of your body between the log cradle and the wedge.
i) Don’t step over the splitter when the motor is running.
j) Always split log along its grain. If across the grain, some types of wood may burst or fly out resulting in injury.
k) If you experienced problems splitting especially hard wood, don’t keep pushing on the handles. Release both
control handles at once, the ram will return. If keep pushing, the ram will fail to retract. If this occurs, turn off the
motor and on again to continue operation.
l) If the log is clipped on the wedge, release both hands, switch off and unplug the power cable immediately. Knock
off the log with a hammer slightly (not with your hands).
m) Never attempt to split more than one log at a time
unless the ram has fully extended and a second log is needed
to complete the separation of the first log. Never attempt to split one log on top of another.
n) Regularly clear the split wood to keep work area tidy for firm footing.
o) Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
p) Never operate your splitter on wet, muddy or icy surface. Safe footing is essential in preventing accidents.
q) Never leave the machine unattended with the motor running.
r) Never use this machine in damp or rainy environment to avoid electric shock or short circuit.
s) Operate log splitter in proper lighting.
t) Never tamper with the motor to run it at excessive speeds. The maximum motor speed is preset by the
manufacturer and is within safety limits.
u) Switch off and unplug power cable quickly when the machine is out of order. For example: the noises becoming
louder and the wedge running erratic indicate there’s a shortage of hydraulic oil in tank for you to add hydraulic
fluid.
v) Don’t pull on power supply cable to unplug.
4. Transportation
Hold the towing handle to move about slowly.
If take the unit for a long distance, please recover the machine as you had unpacked it from the carton.
NOTE:
a) Never move this machine while the motor is running.
b) Be extra cautious when moving this machine on rugged and rough terrain.
c) Be careful to keep upright, not to be tipped or crashed during transportation
d) Never allow anyone to ride on the machine while moving.
5. Maintenance and repair
• Refer to the Components drawing and parts list should it become necessary to disassemble the unit for repair or
replacement of parts.
NOTE:
a) Ensure the power cable is unplugged while performing any maintenance and repair.
b) The hydraulic system is preset at the factory. Don’t adjust the valve.
c) Never alter this machine in any manner under any circumstances. Any alteration circumventing the design
capabilities and capacities of this machine could result in serious injury and will void the warranty.
d) Replace all damaged and worn parts immediately with original equipment manufacturer’s parts only.
e) Wipe unit with an oiled rag to prevent rust. If the wedge becomes dull or nicked, it can be sharpened. Wear
safety gloves while handling the wedge.
f) Never check for leaks of hydraulic fluid with your hand. Escaping fluid under pressure can have sufficient force
to penetrate skin causing serious personal injury or even death. Leaks can be detected by passing a piece of
cardboard over the suspected leak and looking for discoloration.
g) Never loosen or remove hydraulic fittings or the cap of hydraulic tank while the log splitter is running.
h) If the motor is overload for a long time, the thermal protector in it which operating temperature is 130C will
disconnect the power of motor. Switch off and unplug the power cable, cool down the motor for half an hour and
it will connect again for continual operation. If not, it’s
necessary for you to call your dealer for customer support.
9
To Next Page
Loading...