What to do if my Parkside MPKZ 2000 A1 Saw motor does not work?
If the motor of your Parkside Saw isn't working, the cause may be a defective motor, cable, or plug, or the main breaker might be switched off. It is advised that you arrange for a specialist to inspect the machine. Never attempt to repair the motor yourself due to the danger involved. Also, check the fuses and replace them if necessary.
Why does my Parkside Saw motor overheat easily?
Your Parkside Saw motor might be overheating due to overloading or insufficient cooling. To resolve this, avoid overloading the motor while cutting. Also, make sure to remove dust from the motor to ensure optimal cooling.
What to do if the Parkside MPKZ 2000 A1 Saw motor does not reach its full power?
If the motor of your Parkside Saw does not reach its full power, it could be due to overloaded circuits in the network, such as other motors running on the same circuit. To fix this, avoid using any other equipment or motors on the same circuit.
How to fix rough or wavy saw cut with Parkside MPKZ 2000 A1?
If your Parkside Saw cut is rough or wavy, the saw blade may be dull, or the tooth shape might not be appropriate for the material thickness. You should re-sharpen the saw blade and/or use a suitable saw blade.
Why does the Parkside MPKZ 2000 A1 motor start slowly and not reach operating speed?
If your Parkside Saw motor starts slowly and doesn't reach operating speed, possible causes include low voltage, damaged coils, or a burnt capacitor. It is recommended to contact an electrician to check the voltage and arrange for a specialist to inspect the motor and replace the capacitor.
What to do if workpiece pulls away or splinters when using Parkside MPKZ 2000 A1?
If the workpiece pulls away or splinters when using your Parkside Saw, it may be due to excessive cutting pressure or using a saw blade not suitable for the task. Try inserting a suitable saw blade.
Why does my Parkside MPKZ 2000 A1 Saw motor make excessive noise?
If your Parkside Saw motor is making excessive noise, it could be due to damaged coils or a defective motor. It is recommended to arrange for a specialist to inspect the motor.
What to do if my Parkside Saw cut is rough or wavy?
If your Parkside Saw cut is rough or wavy, it could be due to a dull saw blade or a tooth shape that's not appropriate for the material thickness. Try re-sharpening the saw blade or using a more suitable blade.
What to do if my Parkside MPKZ 2000 A1 workpiece pulls away and/or splinters?
If the workpiece pulls away and/or splinters when using your Parkside Saw, it may be due to excessive cutting pressure or an unsuitable saw blade. Try inserting a suitable saw blade.
Why Parkside Saw motor does not reach its full power?
The motor of your Parkside Saw might not reach its full power because the circuits in the network are overloaded (other motors, etc.). Avoid using any other equipment or motors on the same circuit.
General warnings and instructions for safe power tool operation.
Guidelines for maintaining a safe work environment and preventing accidents.
Precautions regarding electrical connections and grounding to prevent shocks.
Verifies the function of the safety guard for user protection.
Steps for assembling and setting up the mitre saw.
Step-by-step guide for replacing the saw blade safely.
General| Power | 2000 W |
|---|---|
| Rated Voltage | 230 V ~ 50 Hz |
| No-Load Speed | 5000 min⁻¹ |
| Cutting Depth at 45° | 45 mm |
| Saw Blade Diameter | 210 mm |
| Weight | 4.2 kg |
| Saw Blade Bore | 30 mm |
| Laser Class | 2 |
| Laser Wavelength | 650 nm |
| Protection Class | II |
| Max cutting depth at 90° | 65 mm |
To Next Page