EasyManua.ls Logo

Parkside PTK 2000 D3 - User Manual

Parkside PTK 2000 D3
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TABLE SAW PTK 2000 D3
TISCHKREISSÄGE
Originalbetriebsanleitung
TABLE SAW
Translation of the original instructions
IAN 298657

Table of Contents

Other manuals for Parkside PTK 2000 D3

Preview: Translation Of The Original Instructions
Translation Of The Original Instructions68 pages

Questions and Answers

  • M
    Mrs. Deborah McfarlandAug 4, 2025
    What to do if my Parkside PTK 2000 D3 Saw engine will not start?
    • P
      Paul BrownAug 4, 2025
      If the Parkside Saw's engine won't start, there are several potential causes: * A blown mains fuse: Check and replace the mains fuse if necessary. * A defective extension cable: Replace the extension cord. * Faulty connections on the motor or switch: Have an electrical specialist repair the connections. * A faulty motor or switch: Have an electrical specialist repair the motor or switch.
  • C
    Chad YoungAug 9, 2025
    Why does my Parkside PTK 2000 D3 leave fire marks on the cutting surface?
    • J
      Jennifer AllenAug 10, 2025
      Fire marks appearing on the cutting surface when using the Parkside Saw can be due to: * A blunt saw blade: Sharpen or change the saw blade. * Using the wrong saw blade: Change the saw blade to the correct one.
  • M
    michaelpaulAug 15, 2025
    What to do if the Parkside PTK 2000 D3 Saw motor won't work, but the fuse is active?
    • B
      bentleyvickiAug 16, 2025
      If the Parkside Saw motor doesn't work but the fuse is active, it could be due to: * Insufficient cross section of the extension cable: Consult the 'Electrical connection' section. * Overload caused by a blunt saw blade: Change the saw blade.
  • A
    Ana WebbAug 22, 2025
    Why is my Parkside PTK 2000 D3 motor rotating in the wrong direction?
    • J
      Jamie LeeAug 22, 2025
      If the Parkside Saw motor rotates in the wrong direction, the possible causes are: * A faulty capacitor: Have an electrical specialist repair the capacitor. * Incorrect connection: Have a qualified electrician exchange the polarity of the outlet.
  • B
    Brad RandolphAug 27, 2025
    How to fix a Parkside PTK 2000 D3 when the blade dissolves after switching off the engine?
    • G
      guzmankellyAug 27, 2025
      If the blade of your Parkside Saw dissolves after switching off the engine, it may be due to a slightly tightened fastening nut. To resolve this, tighten the right hand thread nut.

Summary

Introduction

Intended purpose

Describes the specific use of the table circular saw for cutting wood.

General description

Extent of the delivery

Lists all items included in the package for the table saw.

Safety instructions

Symbols and icons

Explains the meaning of various safety symbols used in the manual.

Symbols in the manual

Safe operation

Outlines essential guidelines for safe and correct operation of the tool.

Additional safety instructions

Safety instructions for handling saw blades

Provides safety guidelines specifically for handling saw blades.

Assembly and Attachment of Tools and Tool Parts

Safety Instructions for Handling the Laser

Safety precautions when using the laser feature.

Important Instructions

Faulty Electrical Connection Cable

Discusses hazards and checks for faulty electrical connection cables.

Assembling the frame and table width extender with length extender

Mounting; adjusting the Riving Knife

Instructions for mounting and adjusting the riving knife.

Replacing the Table Insert

Attaching;changing the Saw Blade

Step-by-step guide for replacing or attaching the saw blade.

Operation

Switching on and off

Instructions on how to turn the table saw on and off.

Adjusting the Cutting Depth

Instructions for setting the desired cutting depth using the crank handle.

Adjusting the Stop Height

How to adjust the stop rail height based on material thickness.

Turning the Stop Rail

Steps to turn the stop rail for different material thicknesses.

Adjusting the Cutting Width

How to adjust the parallel stop for precise cutting width.

Adjusting the Stop Length

How to adjust the stop rail length to prevent workpiece jamming.

Adjusting the Parallel Stop

Instructions for aligning the parallel stop parallel to the saw blade.

Transverse stop

How to set up and use the transverse stop for cross cuts.

Adjusting the scale of the parallel stop

How to calibrate the scale on the parallel stop for accurate readings.

Angle Adjustment

Adjusting the Laser

Instructions for adjusting the laser beam for precise cutting.

Using the Laser

Use

General instructions for using the laser feature for precise cuts.

Performing Longitudinal Cuts

Cutting narrow Workpieces

Guidelines for cutting narrow workpieces using a push stick.

Cutting very narrow Workpieces

Caution! In the case of short workpieces, the push stick should be used from the beginning of the cutting process.

Emphasizes using the push stick from the start for short workpieces.

Performing Bevel Cuts

Performing Transverse Cuts

Steps for performing transverse cuts using the stop.

Cutting Chipboard

Collection bag for wood residues

Information on the use and limitations of the collection bag.

Transport

Cleaning and Servicing

Cleaning

Instructions for regular cleaning of the device.

Storage

Waste disposal and environmental protection

Instructions for proper disposal of the device and its components.

Trouble shooting

Spare parts;Accessories

Lists available spare parts and accessories with their order numbers.

Guarantee

Terms of Guarantee

Details the conditions and duration of the product guarantee.

Repair Service

Processing in Case of Guarantee

Steps to follow for efficient handling of warranty claims or queries.

Service-Center

Importer

Contact information for the product importer.

Translation of the original EC declaration of conformity

Original EG-Konformitätserklärung

The original EC declaration of conformity in German.

Parkside PTK 2000 D3 Specifications

General IconGeneral
Power2000 W
Bevel cut0° to 45°
Laser class2
Blade Diameter254 mm
Idle speed5000 min⁻¹
Mitre cut45°

Related product manuals