Why does Parkside Saw motor make excessive noise?
If your Parkside Saw motor makes excessive noise, it could be due to damaged coils or a defective motor. Arrange for inspection of the motor by a specialist.
Why does my Parkside Saw motor overheat easily?
The motor may be overheating due to overloading or insufficient cooling. Avoid overloading the motor during cutting tasks. Additionally, remove any dust from the motor to ensure it cools effectively.
What to do if my Parkside PKS 1500 A1 Saw motor does not reach its full power?
If the motor isn't reaching its full power, it could be due to overloaded circuits in the network, possibly from other motors or equipment. Try not to use any other equipment or motors on the same circuit.
Why does my Parkside PKS 1500 A1 Saw motor make excessive noise?
Excessive noise from the motor could indicate damaged coils or a defective motor. Arrange for a specialist to inspect the motor.
What to do if the workpiece pulls away and/or splinters when using my Parkside PKS 1500 A1?
If the workpiece pulls away or splinters, it might be because of excessive cutting pressure or an unsuitable saw blade. Insert a suitable saw blade.
What to do if Parkside PKS 1500 A1 Saw motor starts up slowly?
If your Parkside Saw motor starts up slowly and does not reach operating speed, it could be due to voltage being too low, damaged coils, or a burnt capacitor. Contact the utility provider to check the voltage. Arrange for inspection of the motor by a specialist. Arrange for replacement of the capacitor by a specialist.
How to fix Parkside PKS 1500 A1 Saw when motor does not work?
If the motor of your Parkside Saw does not work, the motor, cable, or plug might be defective, or the fuses might have an issue. Check the fuses and replace them if necessary. Arrange for inspection of the machine by a specialist. Never attempt to repair the motor yourself due to the danger involved.
Why is the Parkside Saw cut rough or wavy?
If your Parkside Saw cut is rough or wavy, it could be due to a dull saw blade or a tooth shape that isn't appropriate for the material thickness. Resharpen the saw blade and/or use a more suitable saw blade.
What to do if the Parkside PKS 1500 A1 Saw motor does not work?
If the motor of your Parkside Saw does not work, the motor, cable, or plug may be defective, or the fuses may be burnt. Arrange for a specialist to inspect the machine. Never attempt to repair the motor yourself due to danger. Check the fuses and replace them if necessary.
Why doesn't my Parkside PKS 1500 A1 motor reach its full power?
If your Parkside Saw motor isn't reaching its full power, it might be because the circuits in your network are overloaded with other equipment or motors. To resolve this, avoid using other equipment or motors on the same circuit while operating the saw.
Lists items included in the package for the mitre saw.
Provides detailed specifications such as dimensions, weight, and cutting capacity.
Details the noise levels (LDA, LWA) and vibration values during operation.
Covers keeping the work area orderly, environmental factors, and lighting.
Emphasizes protection from electric shock, keeping others away, and wearing suitable clothing.
Details correct usage, avoiding overloading, and using the right tool for the job.
Covers saw blade use, personal protective equipment, and dust collection.
Instructions on keeping tools sharp, checking cables, and avoiding inadvertent starting.
Guidelines for using insertion tools, speed, and saw blade condition.
Precautions for avoiding eye exposure to the laser beam.
Instructions on inserting, charging, and handling batteries safely.
Addresses potential hazards like electrical shock and excessive pressure.
Steps for unpacking, moving, transporting, positioning, and connecting the machine.
Details on installing dust bag, work piece clamp, and supports.
Defines intended and unintended uses, and cutting data.
How to pivot the table plate and tilt the saw unit.
Steps for fixing workpieces, cross-cutting, and replacing the saw blade.
Instructions for changing laser batteries and connecting the machine to power.
Information on dust extraction systems and general maintenance tasks.
General| Power | 1500 W |
|---|---|
| Blade Diameter | 190 mm |
| Cutting Angle | 0° - 45° |
| Weight | 4.6 kg |
| No-load speed | 5000 rpm |
| Cutting depth max. at 0° | 65 mm |
| Cutting depth max. at 45° | 45 mm |
| Cable length | 2 m |
| Max cutting depth at 90° | 65 mm |
| Cutting Depth | 65 mm |
| Saw blade | 190 mm |
To Next Page
