Peavey Ecoustic 112 User Guide

SPECIFICATIONS
Rated Power & Load:
100 W RMS into 4 ohms
Power @ Clipping: (typically)
(I % THD, 1 kHz, 120 V AC line)
100 W RMS into 4 ohms
Frequency Response:
+O, -3 dB, 40 Hz to 20 kHz
@ 80 W RMS into 8 ohms
Hum & Noise:
Greater than 90 dB below rated power
Power Consumption:
Domestic: 300 W @ 60 Hz, 120 V AC
Export: 300 W @ 50160 Hz, 220-230/240 V AC
PREAMP SECTION
The following specs are measured @ 1 kHz with the controls
preset as folio ws:
All equalization sliders @ 0
Feedback frequency @ 40 Hz
Notch @ 0 (full clockwise)
Reverb Sends @ 0
Master Reverb @ 0
Master Presence @I 0
Nominal Levels are with normal volume @ 5
Minimum Levels are with normal volume @ 10
System Hum & Noise @ Nominal Input Level:
(20 Hz to 20 kHz unweighted)
72 dB below rated power
Instrument Input: (passive)
Impedance: High-Z, 2.2 M ohm
Nominal Input Level: -25 dBV, 55 mV RMS
Minimum Input Level: -44 dBV, 6 mV RMS
Maximum Input Level: 0 dBV, 1 V RMS
Instrument Input: (active)
Impedance: High-Z, 44 K ohms
Nominal Input Level: -14 dBV, 200 mV RMS
Minimum Input Level: -32 dBV, 25 mV RMS
Maximum Input Level: 15 dBV, 5.5 V RMS
Microphone Input: (Low-Z balanced)
Impedance: Low-Z, IO K ohms
Nominal Input Level: -38 dBV, 12 mV RMS
Minimum Input Level: -50 dBV, 3 mV RMS
Maximum Input Level: -6 dBV, 500 V RM
Phantom Powered: /I 5V
Microphone Input: (High-Z)
Impedance: High-Z, 100 K ohms
Nominal Input Level: -16 dBV, 160 mV RMS
Minimum Input Level: -30 dBV, 33 mV RMS
Maximum Input Level: 20 dBV, IO V RMS
Equalization:
Special 5-band active type EQ
Presence: +I0 dB @ 5 kHz
Feedback Control:
Notch: 20 db
Frequency Range: 40 Hz to 2 kHz
Effects Send:
Load Impedance: 1 K ohm or greater
Nominal Output Level: -10 dBV, 300 mV RMS
Effects Return:
Impedance: High-Z, 22 K ohms
Designed Input Level: -10 dBV, 300 mV RMS
(Switching jack provides Effects Send to Effects Return
connection when not used.)
Preamp Output:
Load Impedance: 1 K ohm or greater
Nominal Output Level: 0 dBV, 1 V RMS
Power Amp Input:
Impedance: High-Z, 22 K ohms
Designed Input Level: 0 dBV, 1 V RMS
(Switching jack provides Preamp output to Power Amp input
connection when not used.)
Direct Output: (transformer balanced)
Load Impedance: 600 ohms or greater
Nominal Output Level (Post EQ): -3 dBV,
0.7 V RMS
External Footswitch Functions:
Instrument Channel Effects Loop Bypass
Amplifier Mute
Dimensions & Weight:
20.0" H x 23.5” W x 11.25” D
44.9 Ibs.
7

Peavey Ecoustic 112 Specifications

General

Brand	Peavey
Model	Ecoustic 112
Category	Musical Instrument Amplifier
Language	English