Peavey PVXp 10

Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
www.peavey.com
Warranty registration and information for U.S. customers available online at
www.peavey.com/warranty
or use the QR tag below
Features and specications subject to change without notice.
Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The passive loudspeaker system shall have a frequency response from 74 Hz to 18 kHz. The peak SPL with inaudible distortion shall reach 122 dB with
music as a source, when measured at a distance of 1M and driven to full output capacity. Power handling shall be rated at 200W continuous, 400W
program and 800W peak. The system shall utilize a Peavey heavy-duty 10" heavy-duty woofer and a Peavey RX 10N dynamic compression driver .
The nominal radiation pattern shall be 100° in the horizontal plane, and 60° in the vertical plane. Axis of the vertical main polar lobe is angled down 10
degrees, resulting in the angular pattern with respect to straight ahead being +20, -40 degrees
The loudspeaker system shall have an input consisting of 1/4" phone jack in parallel with an NL-4 4-pin twist-lock jack on the rear panel. Impedance
shall be 8 ohms nominal.
The input signal shall be divided into high frequencies and low frequencies by a passive high level crossover at 3.0 kHz. The enclosure shall be
constructed of injection-molded ABS with a UL ame rating, and reinforcing ribs internally. A handgrip shall be incorporated on the top rear of the
cabinet, and on the right side.
A separate powder-coated metal grille shall be provided for horn and woofer protection. The cabinet shall incorporate a pole mount for speaker stand
use, four tall sturdy rubber feet for oor standing use, and a group of two widely spaced inserts, and a rectangular grouping of four mounting point
inserts on the top and bottom each, for ying use.
The outside dimensions shall be: 20.00" (50.8 cm) tall x 12.69" (32.2cm) wide x 11.06" (28.1 cm) deep, and the weight shall be 25 lbs (11.3 kg). The
loudspeaker system shall be called a Peavey PVX™10 .
12.690
20.000
11.060
10.303 9.594
4.701
1.479
6.804
1.977
7.547
4.567
17.165
4.528
6.694
6.694
1.378
7.874
2.165
9.449
2.500
2.500
3.740
3.740
2.087
4.331
4.724
6.694
2.500
2.500
4.534
7.283
3.740
3.740
PVX 10
12.690
20.000
11.060
10.303 9.594
4.701
1.479
6.804
1.977
7.547
4.567
17.165
4.528
6.694
6.694
1.378
7.874
2.165
9.449
2.500
2.500
3.740
3.740
2.087
4.331
4.724
6.694
2.500
2.500
4.534
7.283
3.740
3.740
PVX 10
12.690
20.000
11.060
10.303 9.594
4.701
1.479
6.804
1.977
7.547
4.567
17.165
4.528
6.694
6.694
1.378
7.874
2.165
9.449
2.500
2.500
3.740
3.740
2.087
4.331
4.724
6.694
2.500
2.500
4.534
7.283
3.740
3.740
PVX 10
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
www.peavey.com
Warranty registration and information for U.S. customers available online at
www.peavey.com/warranty
or use the QR tag below
Features and specications subject to change without notice.
Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278