Pentair Pool Products LEGEND

Other manuals for Pentair Pool Products LEGEND

Installation Guide20 pages

Questions and Answers

W
whiterobertoAug 17, 2025
Why is Pentair Pool Products Swimming Pool Vacuum Legend falling over?
- G
  Glenn CampbellAug 17, 2025
  If your Pentair Pool Products Swimming Pool Vacuum Legend is falling over or lying on its side, it typically indicates that the debris bag needs emptying. Also, check the ballast float for leaks by unscrewing it counter-clockwise and listening for water inside.
B
Brenda StevensAug 21, 2025
What to do if Pentair Pool Products Swimming Pool Vacuum Legend will not back up?
- M
  Margaret HarrisAug 21, 2025
  If your Pentair Pool Products Swimming Pool Vacuum Legend isn't backing up, verify that the Back-Up Valve is cycling correctly by holding the valve out of the water to see if the jet comes on for approximately 30 seconds and shuts off for about 3 minutes and 30 seconds. Also, check the wheel RPM and empty the debris bag if it's full or even half full.
K
kevin94Aug 25, 2025
How to fix Pentair Pool Products Swimming Pool Vacuum Legend hoses tangling?
- J
  Joseph AllenAug 25, 2025
  To resolve tangling hoses on your Pentair Pool Products Swimming Pool Vacuum Legend: * Check the length of the Feed Hose to ensure it is not too long. * Make sure the Feed Hose is floating properly on the surface and that the hose floats are evenly spaced. * Twist the Hose Swivels to ensure they spin freely; replace any that do not. * Lay the Feed Hose straight in the sun to remove any memory.
K
katierubioAug 28, 2025
What to do if Pentair Pool Products Swimming Pool Vacuum Legend will not climb?
- F
  frank86Aug 28, 2025
  If your Pentair Pool Products Swimming Pool Vacuum Legend isn't climbing, even if algae isn't visible, brush the sides of the pool wall. Check the wheel RPM. Reposition the Thrust Jet by loosening the two screws to adjust it. Remember that the climbing ability depends on the pool's shape and water pressure; it climbs better in pools without sharp angles or curves where the floor meets the wall.
C
chavezshawnSep 1, 2025
How to stop Pentair Pool Products Swimming Pool Vacuum sweep hose being sucked into the cleaner?
- T
  Tanya AndersonSep 1, 2025
  To prevent the sweep hose from being sucked into the cleaner of your Pentair Pool Products Swimming Pool Vacuum, adjust the Sweep Hose using the Adjustment Screw located on the bottom of the Swivel Mast, just below the upper Thrust Jet. Turn the Adjustment Screw clockwise until the Sweep Hose moves in a gentle sweeping motion.
K
Karen DavidSep 5, 2025
Why is Pentair Pool Products Swimming Pool Vacuum booster pump very noisy?
- T
  toni10Sep 5, 2025
  If your Pentair Pool Products Swimming Pool Vacuum booster pump is very noisy: * Ensure the Wall Fitting is correctly mounted in the pool wall. * Verify that the Pool Filtration system is functioning properly. * Contact your local Pool Professional, as there might be a Booster Pump problem.
W
William ConwaySep 8, 2025
What to do if Pentair Pool Products Swimming Pool Vacuum sweep hose sprays water?
- J
  Joseph BradleySep 8, 2025
  If the Sweep Hose of your Pentair Pool Products Swimming Pool Vacuum breaks the water surface and sprays nearby areas, adjust the Sweep Hose to ensure it moves in a gentle sweeping motion. You may also consider adding an optional Sweep Hose weight.
S
Sherry WolfeNov 12, 2025
What to do if Pentair Pool Products Swimming Pool Vacuum Legend doesn’t move or moves sluggishly?
- S
  Steve MaddenNov 12, 2025
  If your Pentair Pool Products Swimming Pool Vacuum Legend doesn’t move properly, there are several things to check: * Ensure both the filter pump and booster pump are on and functioning correctly; cleaning your pool filter system might be necessary. * Inspect the Wall Fitting screen for any obstructions and rinse it clean. * Examine the wheel RPM. * Verify if the Back-Up Valve is cycling correctly by holding it out of the water to see if the jet activates for about 30 seconds and then shuts off for approximately 3 minutes and 30 seconds. * Look at all Hose connections and Swivels for any leaks that could be causing a loss of water pressure. * Check for any debris that might be stuck in the gear teeth of the front drive wheels, and gently rotate the front wheels backward to rem...