Pentair AUTOTROL 460TC

Questions and Answers

S
Sheila HutchinsonAug 16, 2025
What to do if the Pentair AUTOTROL 460TC Control Systems timer is stalled in regeneration?
- J
  Joseph OwenAug 17, 2025
  If your Pentair Control Systems timer is stalled in the regeneration cycle, there are several potential causes. It could be due to a dead motor, a motor running backwards, lack of electric power at the outlet, a broken gear, a defective switch, an air leak in brine connections, binding of the camshaft, water pressure exceeding 125 psi during regeneration, or a defective circuit board. Addressing these issues involves actions like replacing the timer, checking junction points for air leaks, removing obstructions from valve discs or the camshaft, installing a pressure regulator or repairing the outlet.
Z
zwalterAug 19, 2025
Why does my Pentair Control Systems clock not show the correct time?
- P
  Paul HarrisonAug 19, 2025
  If your Pentair Control Systems clock isn't displaying the correct time, it might be because the outlet is operated by a switch, the voltage or frequency is incorrect, or there have been power outages. Try using an outlet not controlled by a switch, replacing the timer with one of the correct voltage and frequency, or resetting the clock.
J
Jennifer LeeAug 22, 2025
How to fix Pentair AUTOTROL 460TC Control Systems regenerating at the wrong time?
- M
  Micheal ArmstrongAug 22, 2025
  If your Pentair Control Systems control regenerates at the wrong time of day, it's likely due to power outages or the clock being set incorrectly. To resolve this, reset the clock to the correct time of day.
C
Craig ScottAug 25, 2025
Why do I run out of soft water with Pentair AUTOTROL 460TC Control Systems?
- C
  Corey DonaldsonAug 26, 2025
  If your Pentair Control Systems are running out of soft water between regenerations, it could be due to several reasons: improper regeneration, fouled softener resin, incorrect salt setting, incorrect hardness or capacity settings, increased water hardness, restricted meter turbine rotation, or excessive water usage below 1/5 gallon per minute. You can try repeating the regeneration with the correct salt dosage, using a resin cleaner, setting the salt control to the proper level, correcting the hardness or capacity settings, adjusting the hardness setting, freeing up the turbine and flushing with clean water, or repairing leaky plumbing and fixtures.
J
James MckenzieAug 27, 2025
What to do if Pentair Control Systems won't regenerate?
- V
  Virginia AbbottAug 27, 2025
  If your Pentair Control Systems control will not regenerate automatically or when the button is pressed, possible causes include the electric cord being unplugged, no electric power at the outlet, a defective motor, a broken gear, binding in the gear train, or a defective switch. Suggested solutions include connecting the power cord, repairing the outlet, or replacing the timer.
A
Austin HerreraAug 30, 2025
How to troubleshoot Pentair AUTOTROL 460TC Control Systems clock not showing time?
- J
  Joseph RichAug 30, 2025
  If your Pentair Control Systems clock does not display the time of day, the issue might stem from an unplugged transformer cord, lack of electric power at the outlet, a defective transformer, or a defective circuit board. Try connecting the power, repairing the outlet, replacing the transformer, or replacing the timer.
D
Debra BowmanSep 1, 2025
Why Pentair AUTOTROL 460TC regenerates only when button is pressed?
- J
  Jorge MorenoSep 1, 2025
  If your Pentair Control Systems control will not regenerate automatically but will regenerate when the button is pressed, it could be due to an inoperative water flow display, a defective circuit board, or incorrect hardness and capacity settings. You can refer to the troubleshooting steps for 'No water flow display when water is flowing', replace the timer, or set the hardness and capacity settings to the correct values.
M
mcintyrekimberlySep 4, 2025
What to do if Pentair Control Systems time display is incorrect?
- C
  Corey AverySep 4, 2025
  If the Pentair Control Systems time display shows something other than the time of day, it could be due to electrical interference or a defective circuit board. Try disconnecting power to the unit, restoring power, and resetting the time of day display, or replacing the timer.
J
Joshua AdamsSep 7, 2025
Why does Pentair AUTOTROL 460TC Control Systems have continuous regeneration?
- M
  Michelle SimmonsSep 7, 2025
  If your Pentair Control Systems has continuous regeneration where the camshaft doesn't stop at the end of regeneration, it could be due to a broken switch activator on the gear or a defective switch. In either case, you should replace the timer.
B
Brittany LuceroSep 10, 2025
What causes no water flow display on Pentair AUTOTROL 460TC Control Systems?
- M
  Mary McdanielSep 10, 2025
  If there's no water flow display when water is flowing in your Pentair Control Systems, it could be due to the bypass valve being in bypass, the meter probe being disconnected or not fully connected, restricted meter turbine rotation, a defective meter probe, or a defective circuit board. Try shifting the bypass valve, fully inserting the probe, removing the meter housing to free up the turbine and flush with clean water, or replacing the timer.

Summary

AUTOTROL 460 i AND 460 TC CONTROL SYSTEM INSTALLATION AND OPERATION INSTRUCTIONS

460 i ELECTRONIC DEMAND SYSTEM

SPECIAL FEATURES 460 i

Memory Retention

Stores data during power outages using NOVRAM for seamless operation.

Self-Adjusting Reserve

Dynamically adjusts reserve capacity based on past usage for economy.

High Water Usage

Reacts to sudden increases in usage by adjusting reserve for anticipated high demand.

Low or No Water Usage

Ignores days with minimal usage for accurate average calculation, e.g., during vacations.

Design Reliability

Features solid-state electronics and a simple metering system for long-term performance.

PROGRAMMING THE 460 i

Time of Day Setting

Sets the current time of day to the nearest hour for regeneration scheduling.

Hardness Setting

Configures the water hardness level (GPG/PPM) for accurate regeneration cycles.

Capacity Setting

Sets the water softener's capacity in kilograins for regeneration control.

CONTROL FEATURES 460 i

Time Display

Shows the current time of day, with PM indicator for accuracy.

Flow Indicator

Flashes when conditioned water flows, confirming meter operation.

Hardness and Capacity Settings

Settings are retained during power outages, no reprogramming needed.

Guest Cycle

Initiates an extra regeneration for periods of high water usage.

PROGRAMMING THE 460 TC

Time of Day Setting

Sets the current time of day for regeneration timing.

Days Setting

Configures the number of days between automatic regenerations.

Clock Setting

Selects between standard AM/PM or 24-hour clock display.

Memory Retention

Retains settings and data during power outages via NOVRAM.

ADJUSTMENT OF BRINE CONTROL 460 i;460 TC

TROUBLESHOOTING

Pentair AUTOTROL 460TC Specifications

General

Power Supply	24 VAC
Control Type	Electronic
Cycle Adjustment	Yes
Voltage	24 VAC
Timer	Digital
Backup	Battery backup
Mounting	Top mount
Warranty	1 year limited
Regeneration	Time initiated
Programming	7-day
Valve Size	1 inch
Frequency	50/60 Hz
Enclosure	NEMA rated