Pentair EVERPURE 1500

To Next Page

PENTAIR EVERPURE 1500 / 2500 / 3500 WATER FILTERS INSTRUCTION & OPERATION GUIDE

1500 / 2500 / 3500 WATER FILTERS

SELECTING A LOCATION

1. Provide a solid mount for the head.

2. Allow minimum clearance of 2½" (6.5 cm) under the cartridge so that it

can be lowered for removal.

3. Allow space for the inlet and outlet water line connections.

MOUNT ONLY IN A VERTICAL POSITION!

OPERATING SPECIFICATIONS

Working Pressure Range: 10 psi (0.7 bar) - 125 psi (8.6 bar), non-shock

Temperature: 35-100° F (2-38° C)

Flow Rate: 0.5 gpm (1.89 Lpm)

For Cold Water use only.

1500/2500/3500 Drinking Water System Capacity:

Model 1500, using 1500 replacement cartridge: Capacity: 750 gal. (2,839 L)

Model 2500, using 2500 replacement cartridge: Capacity: 1,500 gal. (5,677 L)

Model 3500, using 3500 replacement cartridge: Capacity: 300 gal. (1,136 L)

Notes

All Everpure

Drinking Water Systems must be maintained according to the manufacturer’s instructions, including the timely

replacement of the filter cartridges. Check for compliance with state and local laws and regulations. For service and replace-

ment parts, contact an authorized Everpure distributor or the Everpure factory.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the

system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

INSTALLATION

1. Before installing the system, determine the bracket position from the illustrations to

the right, best suited to accommodate the inlet and outlet water line connections.

2. Using the bracket as template, mark and set the provided bracket mounting screws

and star washers (or bolts if preferred).

3. Install 1/4" compression fitting into the head. Take care not to cross-thread the

fittings. Be sure to use plumbers tape or a good quality pipe joint compound on the

fitting threads.

4. Bring the inlet and outlet tubing to the head fittings and attach. Double check the

connections to be sure water will follow the direction-of-flow arrow on top of the

head; water supply to the inlet fitting and your faucet to the outlet fitting.

5. Install a cartridge following the instructions on back page.

Illustration A

Bracket Angled

45º to Left

Illustration B

Bracket Angled

45º to Right

Illustration C

Bracket

Straight Back

2" (5.0 cm) Allowance for

cartridge insertion

Unit Dimensions with:

• Everpure 1500 Cartridge:

⁄4" (32.4 cm)

• Everpure 2500 Cartridge:

⁄4" (45.1 cm)

Need help?

Do you have a question about the Pentair EVERPURE 1500 and is the answer not in the manual?

Summary

Selecting a Location for Your Water Filter

Mounting Requirements

Ensure a solid mount, clearance for cartridge removal, and space for water line connections. Mount only in a vertical position.

Operating Specifications and System Capacity

System Capacity by Model

Details the water capacity for models 1500, 2500, and 3500 using their respective replacement cartridges.

Installation Guide

Bracket Placement and Fitting Installation

Determine bracket position, mark and set mounting screws, install compression fittings, and connect water lines following flow direction.

Cartridge Change and System Startup

Cartridge Removal and Replacement Procedure

Steps for shutting off water, relieving pressure, removing the old cartridge, and installing a new one correctly.

Startup and Purging Process

Instructions for running water through the faucet for three minutes to precoat and purge the new cartridge.

Separate Faucet Installation Guide

Installation for Separate Faucets

Guidance for installations using a separate faucet kit, noting fittings for plastic and copper tubing.

Summary

Selecting a Location for Your Water Filter

Mounting Requirements

Ensure a solid mount, clearance for cartridge removal, and space for water line connections. Mount only in a vertical position.

Operating Specifications and System Capacity

System Capacity by Model

Details the water capacity for models 1500, 2500, and 3500 using their respective replacement cartridges.

Installation Guide

Bracket Placement and Fitting Installation

Determine bracket position, mark and set mounting screws, install compression fittings, and connect water lines following flow direction.

Cartridge Change and System Startup

Cartridge Removal and Replacement Procedure

Steps for shutting off water, relieving pressure, removing the old cartridge, and installing a new one correctly.

Startup and Purging Process

Instructions for running water through the faucet for three minutes to precoat and purge the new cartridge.

Separate Faucet Installation Guide

Installation for Separate Faucets

Guidance for installations using a separate faucet kit, noting fittings for plastic and copper tubing.

The Pentair Everpure 1500/2500/3500 Water Filters are designed to provide filtered water for various applications, primarily focusing on improving water quality for drinking and other uses. These systems are certified by NSF International against NSF/ANSI Standards 42 and 53 for the reduction of both aesthetic and health effects.

Function Description

The primary function of these water filters is to remove impurities from water, enhancing its taste, odor, and safety. They achieve this through mechanical filtration and chemical reduction. Specifically, the systems are certified for:

Aesthetic Effects (Standard 42):
- Chemical Reduction: Reduces chlorine.
- Mechanical Filtration: Reduces nominal particulate (Class I).
- Taste and Odor Reduction.
Health Effects (Standard 53):
- Mechanical Filtration: Reduces cysts.
- Asbestos reduction (for 1500 model only).
- VOC (Volatile Organic Compounds) reduction (for 3500 model only).
- Lead reduction (for 3500 model only).

The system operates by directing water through a cartridge that contains filtration media. The specific capabilities vary depending on the model (1500, 2500, or 3500) and the corresponding replacement cartridge used.

Important Technical Specifications

Working Pressure Range: 10 psi (0.7 bar) - 125 psi (8.6 bar), non-shock. This indicates the safe operating pressure limits for the system.
Temperature: 35-100° F (2-38° C). The system is designed for cold water use only within this temperature range.
Flow Rate: 0.5 gpm (1.89 Lpm). This specifies the rate at which filtered water is delivered.
Unit Dimensions (with cartridge):
- Everpure 1500 Cartridge: 12¾" (32.4 cm)
- Everpure 2500 Cartridge: 17¾" (45.1 cm)
- The 3500 cartridge dimensions are not explicitly listed but would be similar to the 2500 given the shared head design.
Capacity (based on replacement cartridge):
- Model 1500 (using 1500 cartridge): 750 gal. (2,839 L)
- Model 2500 (using 2500 cartridge): 1,500 gal. (5,677 L)
- Model 3500 (using 3500 cartridge): 300 gal. (1,136 L)

Usage Features

Installation Flexibility: The system can be mounted in various orientations (bracket angled 45° to left, 45° to right, or straight back) to accommodate different plumbing setups. However, it must always be mounted in a vertical position.
Compact Design: Requires a minimum clearance of 2½" (6.5 cm) under the cartridge for removal and space for inlet/outlet connections. A 2" (5.0 cm) allowance is needed for cartridge insertion.
Easy Cartridge Replacement: The cartridge change procedure is designed to be straightforward:
1. Shut off water supply and relieve pressure.
2. Turn the cartridge to the left (clockwise) approximately ¼ turn.
3. Pull the cartridge downward and out.
4. Align the new cartridge lug with the head label.
5. Press the new cartridge fully up into the head.
6. Turn the cartridge to the right (counterclockwise) as far as possible.
7. Turn water back on.
Start-up Procedure: After cartridge replacement, filtered water should be run through the faucet for three minutes to precoat and purge air from the cartridge.
Cold Water Use Only: The system is specifically designed and certified for use with cold water.
Inlet/Outlet Connections: Accommodates ¼" soft plastic tubing with compression fittings. For copper or hard plastic tubing, nuts with metal grippers are recommended.

Maintenance Features

Timely Cartridge Replacement: All Everpure Drinking Water Systems require timely replacement of filter cartridges according to manufacturer's instructions to maintain optimal performance and compliance with certifications. The capacity specifications (750, 1500, or 300 gallons) serve as a guideline for replacement frequency, though actual frequency may vary based on water quality and usage.
Disinfection Requirement: It is crucial not to use the system with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. However, systems certified for cyst reduction can be used on disinfected waters that may contain filterable cysts.
Service and Parts: For service and replacement parts, users are directed to contact an authorized Everpure distributor or the Everpure factory.
Installation Date Marking: The cartridge provides a space to note the installation date, aiding in tracking replacement schedules.
Compliance: Users are advised to check for compliance with state and local laws and regulations regarding water filtration systems.