Pentair NRG-Temp - Operation EcoHome;EcoOffice Mode; Getting Started

25
Factory set value:
The factory value is depending on the active sensing
mode:
• In floor sensing mode = 35°C
• In room sensing mode = 27°C
• In room sensing mode with floor limiter = 27°C
7.1.8 USER MENU 8: MINIMUM TEMPERATURE
SET POINT FOR THE ROOM SENSOR
You can define a minimum temperature set point. It
is then not possible to change the temperature in the
Comfort (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
), Auto (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
) or Reduced (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
) temperature
under this minimum set-temperature when you are
operating in room sensing mode.
Possible values: 5 to 15°C
Factory set value: 5°C
7.1.9 USER MENU 9: MAXIMUM TEMPERATURE
SET POINT FOR THE ROOM SENSOR
You can define a maximum temperature set point. It
is then not possible to change the temperature in the
Comfort (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
), Auto (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
) or Reduced (
[ ]
R
C
EcoHome
EcoOffice
Standby
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
•
0h
•
3
• •
6
• •
9
• •
12
• •
15
• •
18
• •
21
• •
24
) temperature
above this maximum set-temperature when you are
operating in room sensing mode.
Possible values: 10 to 40°C (the minimum difference
between the Minimum and Maximum set point for
the room sensor is 5°C)
Factory set value: 40°C
7.2 THE INSTALLERS OR ADVANCED USER
MENUS
7.2.1 USER MENU A: ADAPTIVE FUNCTION (ITCS –
INTELLIGENT TEMPERATURE CONTROL SYSTEM)
The Adaptive function calculates when the heating
needs to be switched on to make sure the comfort
temperature is reached when required. If the
Adaptive function is switched OFF, the heating will
start at the programmed time.