C
S
himemode
irenmode
d
1
2
The detection range of the sensor can be adjusted using the range
adjuster [3]. Set this at the minimum level required for the desired
detection.At the maximim range setting the unitsensor is very sensitive
andmayreacttootherdisturbances.
Usetheadjuster[4]tosetthedesiredvolume.
To disarm the unit and to cancel the reaction to movement press the
buttons[10]or[16].TheLED[5]isnolongerilluminated.
To manually activate a siren sound for approx. 20 sec. Press the panic
button [18] on the remote control. This function can be activated when
the unit is in armed or disarmed mode. If the unit was in the armed
modeitwillremainarmedafterthe20sec.siren.
Tocancelthe siren sound within 20sec.Pressthebutton[10]or[16].If
theunitwasarmed,itwillnowbedisarmed.
To turn off the unit turn the button [4] to the position "OFF" (a click
soundcanbeheard).Afterashortpause,thepowerLED[6] isnolonger
illuminated.
To turn on the unit into standby mode turn the button [4] clockwise to
therequiredvolumesetting.
T
AdditionalremotecontrolEW01R(max.1x)(Art.-No.33557)/MA80R
a
Wirelessdoor/windowcontactMA80KM(Art.-No.33552)
WirelessPIR-movementdetector(indoor)MA80P(Art.-No.33551)
E
Install the batteries into the wireless component. Ensure that the main
unitisnotarmed,theLED[5]isnotilluminated.
DepresstheLEARNbutton[8]untilapeepsoundcanbeheard.Theunit
isnowinthelearningmodefor20sec.(LED[5]flashes).
Move within the detection area of the MA80P, or separate the magnet
away from the reed switch of the MA80KM, or press a button on the
EW01R/MA80R.Acodedsignalwillbetransmittedtothemainunit.
Twolongpeepsoundswillconfirmthesuccessfulenrollmentof the code
ofthecomponentintothemainunit.
Ifwithin20sec.nocomponenthasbeenenrolledthelearningmodewill
beautomaticallycancelled.Thisissignalledby4peepsounds.
Repeat the above stepsfor each component. If a componentis enrolled
forasecondtimethefirstenrollmentisautomaticallycancelled.
I
etection 2x"ding-dong”
detectionwithin5sec. 3sec.Siren
ormoredetectionswithin5sec. 20sec.Siren
hefollowingoptionalcomponentscanbeenrolledintothemainunit:
nduptoatotal6xofthefollowingdetectors:
ach wireless component has a unique coding set in the factory. This code
mustbeenrolledintothemainunit:
f a wireless detector is activated (from MA80KM door or window opened,
movement detected by MA80P) when the main unit is armed, then the unit
reactsdependingonthemodesettingasfollows:
1/
D
0. Addingoptionalwirelesscomponents
eleting all the wireless components
!
!
!
!
!
!
!
#
#
#
!
!
!
!
!
!
#
#
#
#
#
!
!
!
!
#
#
#
!
!
!
!
Avoid metal doors, cupboards and similar objects in the detection area
(seeFig.D,IandIII).
Ensure that there are no heat sources, microwave ovens or wireless
surveillance cameras within the detection area, these can cause false
triggering.
Place the main unit inside the property with the back side towards the
wallon the othersideof which themovement is to bedetected, eg. next
tothefrontdoororpatiodoor.
Place the main unit, if possible on a table or shelf directly against the
wall(seeFig.D,IIandIV).
You can also hang the unit on the wall at a height approx. 0.8 - 1.5m
fromthefloor:
Drilltwosuitableholeswithahorizontalseparationof5cm.
Ifrequired,placethesuppliedwallplugs[22]intotheholes.
Secure the supplied screws [23] so that the screw heads protrude
5 mm outofthewall.
Hang the main unit on the wall so that the hanging slots [7] are
locatedoverthescrewheads.
Pushtheswitch[9]totherequiredposition:
B
C
S
Turntherangeadjuster[3]totheposition"MAX".
Turnthevolumeadjuster [4] to the required volume.The powerLED[6]
lights(colour:seechapter11)andtheunitisnowinstandbymode.
Toarmtheunit,press the I/O button [10] or [17].The armedmode will
beindicatedby illuminationofthearmLED[5]andaudiablyby:
B
C
S
A
I
1
2
3
Note:
B
Test the function and the detection area from the proposed
locationbeforedrillingtheholes.
The microwave sensor does not detect through the aluminium coated
walls.Canbeusedbehindcurtainsdirectlythroughplasticwindows.
The microwave sensor does not detect through coated or wired glass or
doubleglazing
Electricalfieldscancausepermanenttriggering
arkmode
himemode
irenmode(upperorlowerposition,thereisnodifference)
arkmode 1xbark
himemode 2x"ding-dong"
irenmode 3peeps
fterawarmupperiod ofapprox.60sec.thereadinessofthedetectoris
signalledbyonepeep.
fmotionisdetectedtheunitreactsaccordingtothesetmode:
detectionwithin5sec. 1bark
detectionswithin5sec. 3Xbark
ormoredetectionswithin5sec. 10sec.Bark
Donot place:
Throughwalls fcaravans
Throughglass windows
Nexttowalls containingelectricalwiring
9. Use
arkmode
GB-20
To Next Page
Loading...
