EasyManuals Logo

Performance Tool W50076 User Manual

Performance Tool W50076
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
2
SAFETY GUIDELINES / DEFINITIONS
UNPACKING AND INSPECTION
SPECIFICATIONS
Specifications are
subject to change
without notice.
Temperature ......................................................... 572 - 932 °F
Wattage .......................................................................1,500 W
Ampage ..........................................................................12.5 A
Voltage .............................................................. 120V AC 60Hz
WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate
or maintain this product. Failure to comply with the instructions may result in serious personal injury and/or
property damage!
The following signal words are used to emphasize safety warnings that must be followed when using this product:
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and
troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction manual are
based upon the latest product information available at the time of publication. The manufacturer reserves the right to
make product changes at any time without notice.
DANGER Indicates an imminently hazardous
situation that, if not avoided, WILL result in death or
serious injury.
WARNING Indicates a potentially hazardous
situation that, if not avoided, COULD result in death
or serious injury.
CAUTION Indicates a potentially hazardous situation
that, if not avoided, MAY result in minor or moderate
injury.
NOTICE Indicates important information, which if
not followed, MAY cause damage to equipment.
After opening the carton, unpack your new product and related parts & accessories. Please inspect it carefully for
any damage that may have occurred during transit. Please check it against the photograph on carton. If any parts
are missing, please call customer service at 1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time.
WARNING DO NOT operate this product if damaged during shipment, handling or misuse. Do not operate the
product until the parts have been replaced or the fault rectified. Failure to do so may result in serious personal
injury or property damage. All damaged parts must be repaired or replaced as needed prior to operating this
product. Check to see that all nuts, bolts and fittings are secure before putting this product into service. If you have
any questions, or require assistance with damaged or missing parts, please contact our factory customer service
department at: 1-800-426-1262.
Please have the serial number, model number, and date of purchase available for reference when calling.
IMPORTANT SAFETY INFORMATION
WARNING
HEAT GUNS ARE A SOURCE OF VERY HIGH TEMPERATURE FLAMELESS HEAT. AS WITH OTHER PRODUCTS
WHICH GENERATE EXTREMELY HIGH TEMPERATURES, READ, UNDERSTAND AND FOLLOW ALL
INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS PRODUCT. FAILURE TO DO SO MAY RESULT IN
FIRE, ELECTRICAL SHOCK, PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
1. Always use common sense and pay particular
attention to all the DANGER, WARNING, CAUTION
and NOTICE statements of this manual. The safety
instructions provided are not intended to cover all
possible conditions and practices that may occur
when operating, maintaining and cleaning power
tools.
2. Observe work area conditions. Do not use machines
or power tools in damp or wet locations. Don’t ex-
pose to rain or snow. Keep work area well lighted. Do
not use electrically powered tools in the presence of
ammable gases or liquids. Do not bring combustible
materials near the tools. Power tools create sparks,
which may ignite the dust or fumes. Do not immerse
tool in liquids. Keep work area clean, well ventilated
and well lit. Cluttered work areas invite accidents.
3. Use personal protective equipment. Wear ANSI ap-
proved safety goggles. Protective equipment such as
dusk mask, non-skid safety shoes, hard hat, heavy
duty work gloves or hearing protection used for
appropriate conditions will reduce personal injuries.
4. Keep bystanders, children and visitors away while
operating this product. Distractions can cause you to
lose control.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Performance Tool W50076 and is the answer not in the manual?

Performance Tool W50076 Specifications

General IconGeneral
BrandPerformance Tool
ModelW50076
CategoryPower Tool
LanguageEnglish

Related product manuals