To Next PageTo Next Page
Need help?Do you have a question about the Philips 42PFL9664H/12 and is the answer not in the manual?
General| Resolution | 1920 x 1080 pixels |
|---|---|
| Display Technology | LCD |
| Screen Format | 16:9 |
| Brightness | 500 cd/m² |
| HDMI Ports | 4 |
| Component video (YPbPr/YCbCr) in | 1 |
| Common Interface (CI) | Yes |
| Contrast Ratio (Dynamic) | 80000:1 |
| Viewing Angle | 176° |
| Screen Size | 42 inches |
| RMS Rated Power | 20 W |
Details product information, getting started guides, user manuals, FAQs, and software drivers.
Information available for download from Philips support websites.
Overview of all input and output connectors on the TV.
Refers to Block Diagrams for PWB/CBA locations.
Essential safety regulations and checks to perform during and after repairs.
Important cautions regarding ESD, high voltage sections, and component handling.
General guidelines for measurements, schematic conventions, and spare parts.
A comprehensive list of abbreviations used in the manual.
Instructions for routing and managing cables within the TV chassis.
Describes safe and convenient positions for servicing the TV set.
Step-by-step guide for removing internal components like the rear cover and speakers.
Procedures for reassembling the TV set after repairs, emphasizing cable placement and EMC foams.
Guides on using test patterns via ComPair for diagnostics.
Explains Service Default Mode (SDM) and Service Alignment Mode (SAM).
Details on error code display, buffer reading, and common error types.
Describes how to activate and interpret error codes indicated by the front LED.
Practical advice for troubleshooting common issues like Ambilight and audio amplifier replacement.
Specifies the environmental and electrical conditions required for performing alignments.
Details the software-based alignments available in SAM mode, such as Tuner AGC and White Point.
Explains how to set option codes for correct communication with ICs and system configuration.
Describes the mandatory NVM reset procedure for repaired Service SSBs.
Overview of the Q549.6E LA chassis and its key components.
Details the power supply unit configuration and output voltages for the platform.
Describes the main processor (PNX8543) responsible for video and audio processing.
Explains the architecture of the Ambilight system, including ARM controller and LED drivers.
Shows the internal block diagram and pin configuration for the TPS53124PW DC/DC converter.
Provides the block diagram and pin configuration for the DRX3926K demodulator IC.
Details the internal block diagram and pin configuration of the PNX8543 stand-by controller.
Presents the block diagram and pin configuration of the TPA3123D Class D audio amplifier IC.
Illustrates the interconnections between major modules like SSB, power supplies, and speakers.
Shows the signal flow for video processing, from front-end to display output.
Depicts the audio signal path, including inputs, processing, and outputs.
Illustrates the control signals and clock distribution across the chassis.
Provides a comprehensive overview of all power supply lines and their connections to different boards.
Circuit diagram for the DC/DC converters, showing voltage regulation and distribution.
Circuit diagram detailing the front-end components, including tuner and AGC amplifier.
Circuit diagram illustrating the functions of the stand-by controller.
Circuit diagram for the PNX8543 control interface, including I2C and EJTAG.
Circuit diagram showing the SDRAM memory interface for the PNX8543 processor.
Circuit diagram illustrating the LVDS interface for the PNX5100 processor.
Circuit diagram detailing the power management and distribution for the PNX5100 processor.
Circuit diagram for the PNX5100 control interface, including I2C and GPIO.
Circuit diagram for the FPGA handling backlight control, LVDS, and I2C multiplexing.
Circuit diagram for the temperature sensor and fan control logic.
Diagram showing the connections for the CI/PCMCIA interface.
Diagram illustrating the pinout and connections for the USB connector.
Circuit diagram for the HDMI switch IC, showing input configuration and EDID control.
Circuit diagram for the analogue external inputs and outputs on the A connector.
Circuit diagram for the analogue external inputs and outputs on the C connector.
Circuit diagram for the analogue external inputs and outputs on the D connector.
