Philips DFA 888 - Technical Specifications

TECHNICAL DATA
(Subject to alteration)
0 Power output acc. to FTC
at 8 ohm load
(20
- 20.000 Hz, D < 0.03%): 75 W continuous sine wave
at 4 ohm load
(20
- 20.000 Hz, D < 0.05%) : 90 W continuous sine wave
0 Power output acc. to IEC
at 8 ohm load
(63
- 12.500 Hz, D < 0.3%): 80 W continuous sine wave
0 Power output acc. to DIN
(1 kHz, D
<0.7%)
at 8 ohm load: 85
W continuous sine wave
at 4 ohm load: 115
W continuous sine wave
at
2 ohm load: 140 W continuous sine wave
0 IHF music power
at 8 ohm load: 95
W
at 4 ohm load: 140 W
at 2 ohm load: 160 W
Harmonic distortion (1 kHz) : 0.0I%
0 Intermodulation distortion: 0.03%
0 Power bandwidth ( - 3 dB) : 10 - 30.000 Hz
0 Frequency response: 20 - 20.000 Hz + 0.5 dB
0 S/N ratio: 90 dB (weighted)
0 Channel separation (1 kHz) : 70 dB
0 Damping factor at 8 ohms: 80
0 Input sensitivity:
Phono MC: 0.25
mV/150 ohm
Phono MM: 2,5
mV/47 kohm
Compact Disc:
150 mV/20 kohm
Tuner: 150
mV/20 kohm
Aux 1
: 150 mV/20 kohm
Aux 2: 150
mV/20 kohm
Tape 1
: 150 mV/20 kohm
DAT/Tape 2
: 150 mV/20 ko h m
Compact Disc optical: 1
x Toslink
Compact Disc: 0.5 V p-p/75 Ohm
DBS/Aux.: 0.5 V p-p/75 Ohm
DAT/Play/Rec: 0.5 V p-p/75 Ohm
0 Outputs:
DAT/Tape
: 150 mV/550 ohm
2 x 2 loudspeakers: 4 - 8 ohm
Headphones: 8-1000
ohm
0 Tone control:
bass:
+ 8 dB to - 8 dB at 100 Hz
treble:
+ 8 dB to - 8 dB at 10 kHz
0 Loudness: +6 dB at 100 Hz, +4 dB at 10 kHz
0 Balance control: 0-co dB
0 Power consumption: 330 W
This product complies with the radio interference requirements
as laid down in EC (European Community) regulations.
Important note for users in U.K.:
The U.K.-version is not fitted with a mains plug
When fitting a mains plug to the mains lead proceed as follows: The wires in the mains lead
are coloured with the following code:
BLUE= NEUTRAL,
BROWN
= LIVE.
As thesecolours may not correspond with the colour markings identifying the terminals in your
plug proceed as follows: The Brown wire must be connected to the terminal which is marked
with the letter L or coloured Red.
The Blue wire must be connected to the terminal which is marked with the letter N or coloured
Black.
Note: This apparatus must be protected by a
3 Amp Fuse if a 13 Amp plug is used or, if any
other type of plug is used, by a
5 Amp Fuse either in the plug or adapter or at the distribution
board. If in doubt consult a qualified
electrician.