Philips FW-C290 - Clock and Timer Functions; Clock Viewing and Setting; Setting the System Timer

24
English
3139 115 20522
Clock/Timer
STAN D BY
-
ON
MINI HIFI SYSTEM
CD1 • 2 • 3 BAND
TAPE 1 • 2
TAPECD TUNER
AUX
PRESET
▲
▲
TUNING
▲ ▲ ▲ ▲
STOP• CLEAR
SEARCH
PLAY• PAUSE PREV NEXT
3 CD ROTARY CHANGER SYSTEM
•
CD REWRITABLE COMPATIBLE
•
CD SYNCHRO RECORDING
•
D
B
B
CDR/VIDEO
JOG
CONTROL
SOUND NAVIGATION - JOG
VOLUME
PROGRAM DIM
RECORD
DUBBING A.REPLAY
INCREDIBLE
SURROUND
CLOCK • TIMER
V
E
C
D
S
C
T
E
C
H
N
O
R
O
C
K
J
A
Z
Z
O
P
T
I
M
A
L
MICROPHONE - LEVEL
DEMO STOP
2
21
3
TUNERTAPE 1/2CD
SLEEP AUXINC.SURR.
DSC VEC
DBB
REPEAT
PAUSE
SHUFFLE
Å
CD DIRECT
VOLUME
á
à
ë
í
É
Ç
View Clock
You can view the clock (if it is set) if the system
is in Standby mode or when any sound source is
selected (CD, TUNER, etc.). The clock will be
displayed for about seven seconds.
¶ Press CLOCK•TIMER briefly (on the system
only).
➜ “PM10:38 or 22:38” (the current time) will
be displayed depending on whether you have
selected 12- or 24-hour mode.
➜ “--:--” will be displayed if the clock is not
set.
Clock Setting
The clock can be set in either 12- or 24-hour
mode, e.g. “AM12:00“ or “00:00“. Before
setting the clock, you must be in the View Clock
mode.
1 Press CLOCK•TIMER to select clock mode.
2 Press PROGRAM to select 12- and 24- hour
mode.
➜ If 12-hour mode is selected, “AM12:00“
starts flashing.
➜ If 24-hour mode is selected, “00:00” starts
flashing.
3 Set the hour with à or á on the system.
4 Set the minute with í or ëon the system.
5 Press CLOCK•TIMER again to store the
setting.
➜ The clock starts.
¶ To exit without storing the setting, press Çon
the system.
Notes:
– During clock setting, if no button is pressed
within 90 seconds, the system will exit clock setting
mode automatically.
– When a power interruption occurs, the clock
setting is erased.
Timer Setting
¶ The system can switch on to CD , TUNER or
TAPE 2 mode automatically at a preset time. It
can serve as an alarm to wake you up.
¶ Before setting the timer, make sure the clock is
set correctly.
¶ The timer will always be switched on once it is
set.
¶ The volume of the timer will increase
from the minimum level to the most
recently selected volume level.
1 Press and hold CLOCK•TIMER for more than
2 seconds to select timer mode.
➜ “AM12:00” or “00:00" or the last timer
setting starts flashing depending on whether you
have selected 12- or 24-hour mode.
➜ The TIMER starts flashing.
➜ The selected source is lit while other available
sources are flashing.
2 Press CD , TUNER or TAPE to select the
desired source.
¶ Before selecting CD or TAPE, make sure a disc
or tape is loaded in the CD tray or tape deck 2.
pg 01-28/C290/21-Eng 29/05/2001, 10:52 AM24